manualshive.com logo in svg

Caroma G Series, Installation And Maintenance Manual, Page: 14 / 16

Share
Download
Caroma G Series Installation And Maintenance Manual Download Page 14

12

MAINTENANCE

If system chemical disinfection is practiced, chlorine can be used (calculated chlorine 

concentration of 50mg/l maximum in water per one hour dwell time) at service interval 

frequency.

FILTER CLEANING INSTRUCTIONS

These models are provided with a stainless steel filter preventing foreign particles to enter the lines. It is 

recommended to clean the filter every six (6) month. If the water flow has decreased, this may be because the 

filter is clogged. The filter can be cleaned as follows:
1.   a. Shut-off the water shut off valve.
 

b. Disconnect the water supply pipe from the adaptor and disassemble the filter.

 

c. Wash the filter under running water.

 

d. Reassemble the parts.

 

e. Restore the incoming water supply and make sure that there is no water leakage.

SOLENOID VALVE SERVICING

The

 

solenoid valve diaphragm requires periodical cleaning every six (6) month. 

Remove the diaphragm from the solenoid valve and examine it for dirt. in case it is dirty or clogged, wash it under 

running water and reassemble it. 

Do not attempt to dismantle the solenoid valve if you are unfamiliar with electronic solenoid valves.

CARE AND CLEANING OF CHROME AND SPECIAL FINISHES
DO NOT

 use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited 

cleaning or maintenance products or substances could damage the surface of the outlet. For surface cleaning of 

outlet us 

ONLY

 soap and water, then wipe dry with clean cloth or towel. When cleaning bathroom tile, the outlets 

should be protected from any splattering of harsh cleansers.

Summary of Contents for G Series

















Reviews:

No comments