Caroma G Series Installation And Maintenance Manual Download Page 13 | Manualshive

Page: 13 / 16

Caroma G Series Installation And Maintenance Manual Download Page 13

11

SECONDS

ABOUT

15

OBJECT

After you have replaced the battery, move away from

the sensor range. Wait 15 seconds in order to allow

the system to set the ideal sensor range. Then after

the self adjustment has taken place the solenoid

valve will be opened and closed for 1 second as an

indication that the ideal sensor range was set and

the product is ready for use.

Check that there are no objects in front of the sensor

after the battery replacement was completed.

Carefully open the dual power input box, using the Allen key provided. Remove the old battery and replace

it with a new 9V battery (Lithium battery is recommended). Close the box.

IMPORTANT:

These models were supplied with a self adjusting sensor.

The ideal sensor range for the specific location will be set automatically again after changing the battery.

I

MPORTANT: Spent batteries should not be disposed of with normal household waste.

Contact your local authority for information on waste disposal and recycling.

BATTERY REPLACEMENT

«
...
11
12
13
14
15
...
»

Summary of Contents for G Series

















Reviews:

No comments