background image

13 

graphing  interference  figures  it  is  necessary  to  swing  in 

the  Bertrand  lena  in  the  magnification  changer  of  the  tube 

adapter  pol. 

10,. 

immersion 

Switching  the  objective  into  the  optical  path: 

Critically  focus  medium- or  high-power  dry  objective  onto 

specimen,  retain  the  focussed  etote. 

Place  immersion  objective  between  two  detent  positions  of 

the  revolving  nosepiece  so  as  to  point  to  the  left  or  right 

front,  In  this  way,  the  specimen  spot  to  be  observed 

becomes  accessible. 

Apply  a  drop  of  immersion  oil  to  the  specimen. 

Switch  immersion  objective  into  working  position. 

Critically  focus  onto  the  image  and  observe  it. 

Removing  the  objective  from  the  optical  path: 

Retain  the  focussed  state  of  the  specimen. 

Swing  out  the  objective  in  such  a  way  that  an  adjacent 

low-power  objective  engages  into  workinq  position 

(other�<�ise,  there  will  be  the  danger  of  moistening  the 

front  lens  of  objectives  of  short  working  distance  with 

oil). 

Change  specimen  or  remove  oil  or  continue  to  work  as 

required. 

11. 

Condenser  immersion 

In  order  to  take  the  high-power  capability  of  the  immer­

sion  objectives  into  account  also  on  the  illumination  side, 

especially  for  conoscopy,  the 

0.95 

achromatic-aplanatic 

condenser  can  be  provided  with  an  immersion  head.  It  is 

advisable  to  remove  the  stop  screw  from  the  underside 

of  the  condenser  changer  when  using  the  immersion  condenser. 

Then  the  condenser  con  be  swung  to  the  left  out  of  its 

engaged  position  so  ttlat  it  is  beside  the  microscope 

stage  at  a  distance  that  allows  to  screw  off  the 

0.95 

Summary of Contents for JENAPOL



































Reviews: