CARL GOLDBERG 120 ARF Instructions Manual Download Page 29

Page: 29 / 30

Mount the two flying wire brackets under the

front mounting screw of the tail wheel brack-

et.

Install the wheel collar with just the set screw

on the axle bracket and insert through the

mounting bracket.

Install the two nylon pushrod fittings on the

ends of the two threaded rods. Screw the

threaded rods into the sides of the other

wheel collar

Install the assembly on the top of the axle

bracket and tighten the set screw. Make

sure the threaded rods are parallel with the

axle.

Place the wheel on the axle and secure with

the wheel collar.

spring fitting

If you have not installed the pushrod fitting for

the tiller springs you will need to remove the

rudder cables and screw them in place.

Install the springs between the rudder horn

and the tail wheel steering arm. Make sure

rudder is centered and tail wheel is straight

ahead.

Summary of Contents for 120 ARF































Search results

Summary of Contents for 120 ARF

Reviews:

Related manuals for 120 ARF

Brands by name

Popular brands

CARL GOLDBERG 120 ARF, Instructions Manual

Search results

Summary of Contents for 120 ARF

Reviews:

Related manuals for 120 ARF

Brands by name

Popular brands