Carimali CENTO50 Installation And Use Manual Download Page 8 | Manualshive

Page: 8 / 25

Carimali CENTO50 Installation And Use Manual Download Page 8

LB-05053-03-GB

Re-filling the boiler.

This operation will automatically stop when the

During this phase all the keypad leds slowly flash

Heating the boiler.

During the heating up phase the display show

During this phase heating of the boiler starts, wait about 20 minutes to reach the set temperature.
This operation will automatically stop when the boiler temperature is

PLEASE NOTE:

All Version

DURING THIS STAGE, KEEP THE STEAM LEVER
WILL RELEASE THE AIR FROM THE BOILER

Check the delivery pressure in the pump gauge by fitting
coffee

dose in order to deliver at 8/9 bars.

Pag. 8

This operation will automatically stop when the level of the probe is reached.

FILLING UP

During this phase all the keypad leds slowly flash simultaneously.

During the heating up phase the display shows the boiler temperature and all the keypad leds light on in sequence

HEATING BOILER

XXX °C

During this phase heating of the boiler starts, wait about 20 minutes to reach the set temperature.
This operation will automatically stop when the boiler temperature is reached, the display shows :

SELECT DRINK

XXX °C

EEP THE STEAM LEVER OPEN FOR A FEW SECONDS, THIS OPERATION

FROM THE BOILER

the pump gauge by fitting

the filter holder filled with properly ground, pressed

in order to deliver at 8/9 bars.

03-04-13

light on in sequence from right to left.

NDS, THIS OPERATION

the filter holder filled with properly ground, pressed

«
...
6
7
8
9
10
...
»

Summary of Contents for CENTO50


























Reviews:

No comments