manualshive.com logo in svg

Carelink CL-MC-XE1-IP-Y, User Manual, Page: 22 / 27

Share
Download
Carelink CL-MC-XE1-IP-Y User Manual Download Page 22

 CL-MC-XE1-IP-Y Series (1/2/4 E1) User Manual

 

- 19 - 

#                    4: 99 ms, 5: 145 ms, 6: 192 ms, 7: 239 ms ). 
# since the packet size is set to 1 (782 Bytes) which is about half
# length of 1514 Bytes, the jitter buffer depth for packet size of
# 782 bytes will be 23msec/2 = 11.5msec 
jitterbd 1 1    
       
#Set the transmit clock source to RxLine for E1 port#1 
#Usage: ceschclkset ch_num clksrc(0:Adaptive/1:Internal/2:RxLine)

ceschclkset 1 2   
 
#Enable E1 port #1, and specifically set the destination IP and MAC
#address of the remote device (CPE). 
ceschset 1 1 172.16.1.2 00:0b:f9:10:01:02 
 
lanset 1 7  
csave                          

Script for setting 

CPE

 site configuration back to default II 

gci 
srcnet 172.16.1.2 255.255.255.0                           
ipset 192.168.2.11 255.255.255.0 172.16.1.1    
cespwidset 1 1 1 
pktsize 1 1  
jitterbd 1 1                   
ceschclkset 1 0 
ceschset 1 1 172.16.1.1 00:0b:f9:10:01:01 
lanset 1 7 
csave 

 

C) Script for resetting CL-MC-XE1-IP-Y to default III   

Script for setting the device back to default III   
(Enable E1 port#1 and port#2 and set LAN bandwidth to 400 kbps) 

Script for setting 

CO

 site configuration back to default III 

gci 
srcnet 172.16.1.1 255.255.255.0 
ipset 192.168.1.11 255.255.255.0  172.16.1.2 
 
#Set both transmitting and receiving pseudowire ID to 1 for E1 port#1

www.carelink.com

Summary of Contents for CL-MC-XE1-IP-Y




























Reviews:

No comments