manualshive.com logo in svg

Carelink CL-MC-XE1-IP-Y, User Manual, Page: 21 / 27

Share
Download
Carelink CL-MC-XE1-IP-Y User Manual Download Page 21

 CL-MC-XE1-IP-Y Series (1/2/4 E1) User Manual

 

- 18 - 

#Configure an ip address for the WAN port 
srcnet 172.16.1.1 255.255.255.0  
 
#Configure an ip address and gateway for the NMS port 
ipset 192.168.1.11 255.255.255.0 172.16.1.2 
 
#Enable LAN port and set the bandwidth to 400Kbps.                  
lanset 1 7 
 
#Save the configuration                             

                 

csave   

Script for setting 

CPE

 site configuration back to default I 

gci 
srcnet 172.16.1.2 255.255.255.0 
ipset 192.168.2.11 255.255.255.0 172.16.1.1 
lanset 1 7 
csave 

 

B) Script for resetting CL-MC-XE1-IP-Y to default II 

 

Script for setting the device back to default II   
(Enable E1 port#1 and set LAN bandwidth to 400 kbps) 

Script for setting 

CO

 site configuration back to default II 

gci 
srcnet 172.16.1.1 255.255.255.0 
ipset 192.168.1.11 255.255.255.0 172.16.1.2 
 
#Set both transmitting and receiving pseudowire ID to 1 for E1 port#1 
cespwidset 1 1 1 
 
#Set the transmit packet size to 782 byte for E1 port#1 
#Usage: pktsize ch_no pkt_size(0~3) ! 
#pkt_size(total len)=> (0: 1514 Byte, 1:782 Byte, 
#                            2:  178 Byte,  3: 306 Byte) 
pktsize 1 1   
 
#Set the jitter buffer depth to 11.5 msec for E1 port#1 
#Usage: jitterbd ch_no depth ! 
#depth(pktsize=0)(0: 11 ms, 1: 23 ms,  2: 40 ms,  3: 75 ms, 

www.carelink.com

Summary of Contents for CL-MC-XE1-IP-Y




























Reviews:

No comments