manualshive.com logo in svg

Carefree TRAVEL'R ADJUSTABLE PITCH, Service Manual, Page: 42 / 48

Share
Download
Carefree TRAVEL'R ADJUSTABLE PITCH Service Manual Download Page 42

Carefree of Colorado

 

O

PERATION

 

The Direct Response system uses 3 switches at the control panel.  Power 
Switch; Patio Switch and Motion Sensitivity Switch. 

P

OWER 

S

WITCH

 

P

OWER 

ON

 ............. The up position activates the Patio switch and the Auto-Retract 

system and provides power to the awning. 

P

OWER 

OFF

 .............. The down position shuts the system down.  The awning cannot be 

extended or retracted in this mode.  The auto-retract system is 
also disabled. 

I

MPORTANT 

N

OTE

: 

The auto-retract system is ON when the power is ON.  The system 

is OFF when the power switch is set to OFF.  If the power is shut off while the awning is 
extended, the awning is not protected by the auto-retract system. 

P

ATIO 

S

WITCH

 

This is a two position momentary contact switch.  This description also applies to 
any additional patio switches that may be installed. 

E

XTEND

 .................. 

Press and release the switch.  The awning automatically 
opens.  To stop the awning before it is fully open, press and 
release the extend switch a second time. 

R

ETRACT

 ................ 

Press and release the switch.  The awning automatically 
retracts until it is fully closed.  To stop the awning before it is 
closed, press and release the retract switch a second time. 

M

OTION 

S

WITCH

 

HIGH

 

↔

 

MED

 

↔

 

LOW 

Low requires less amount of motion before the awning closes automatically. 
High requires more motion before the system closes automatically. 

You may have to experiment to find the best setting for your preferences. 

NOTE:  

If the motion switch is not installed, the system defaults to the medium setting. 

Press to

Retract

Press to

Extend

Power

ON

Power

OFF

Hi

Low

Motion

Sensitivity

Med

DR039

Summary of Contents for TRAVEL'R ADJUSTABLE PITCH

















































Reviews:

No comments