manualshive.com logo in svg

Carefree TRAVEL'R ADJUSTABLE PITCH, Service Manual, Page: 28 / 48

Share
Download
Carefree TRAVEL'R ADJUSTABLE PITCH Service Manual Download Page 28

Carefree of Colorado

Service Manual

T

RAVEL

'

R

 

052540-301r10 

25 

Item Part 

Number 

Description 

Notes 

1 

NLA 

1/2 Set Hardware, Arm Assy, Motorized, RH 

Flat Pitch

1,2,7 

R001507XXX 

1/2 Set Hardware, Arm Assy, Motorized, RH 

Steep Pitch

1,2 

2 

NLA 

1/2 Set Hardware, Arm Assy, Idler, LH 

Flat Pitch

1,2,7 

R001508XXX 

1/2 Set Hardware, Arm Assy, Idler, LH 

Steep Pitch

1,2 

3 

R001094XXX 

Top Mounting Bracket 

Used w/ Aftermarket Only

1 

4 

SG0014 

Quick Mount Bracket Kit  (includes 4 brackets and hardware) 

White

1 

SG0015 

Quick Mount Bracket Kit  (includes 2 brackets and hardware) 

Black

1 

5 

R001740XXX 

Fascia, 11", Flat Pitch 

qty: 1

1,3 

R001740XXX 

Fascia, 3", Steep Pitch 

qty: 2

1 

6 

R001252 

Gas Shock, 42.5" extended length (clevis to clevis) 

Flat Pitch

R001331 

Gas Shock, 37" extended length (clevis to clevis) 

Steep Pitch

7 

R001576 

Shock Hardware Kit 

8 

R001104XXX 

Motor Assy 

Series I

1 

9 

R001323 

Kit, Head Attach Hardware 

Series I

1 

10 

R001324XXX 

Kit, Motor Cover 

Series I

1,4 

11 

R001326XXX 

Kit, Motor Assy 

Series II

1,5 

12 

R001328XXX 

Kit, Motor Cover 

Series II

1,4 

13 

R060414-006 Cable, 

Motor 

14 

R001107XXX 

Idler Assy  

Series I

1 

15 

R001325XXX 

Kit, Idler Cover 

Series I

1,4 

16 

R001327XXX 

Kit, Idler Assy  

Series II

1,5 

17 

R001329XXX 

Kit, Idler Cover 

Series II

1,4 

18 

19xx00 

Roller Tube,3-slot 

3 1/2" Dia

19 

Canopy 

Refer to Canopy Order Form

20 

20xx36XXX Alumaguard 

Assembly 

Only

1

21 

R001246XXX-xxx Uniguard 

(includes 4.25" soft connect) 

1 

R001246XXX-xxxT Uniguard 

(includes 5.25" soft connect) 

1 

22 

R001247XXX-xxx 

Soft Connect 

4.25" Wide

1 

R001247XXX-xxxT  Soft Connect 

5.25" Wide

23 

901067 

Tractioner 

set of two

24 

R001605 

Kit Single Switch 

6 

25 

R014634-025 

Extension Kit, White 

The following parts are not shown

 

26 

R014492-251 

Hardware Pack, w/ Top Bracket 

White

27 

R014489-JV1 

Hardware Pack, w/ Top Bracket 

Black

28 

R001697 

Replacement Roller Kit 

Single Arm

Notes:  1.  XXX = Color; xx = Length in inches.  WHT=White; BLK=Black 

2.

Arm assemblies are configuration specific and cannot be interchanged.  When ordering, provide
the following information: part number, serial number, flat/steep pitch.

3.

Fascia kit includes one fascia and screws.

4.

Head cover kits include one front cover, one rear cover and screws.

5.

Series II replacement motor and idler assemblies includes screw and nut.

6.

Switch kit includes switch, faceplates, screws and connector.  Kit replaces all previous single
switch kits.

7.

The Fixed Flat Pitch Travel'r has been discontinued.  For replacement arm options, contact
Carefree Customer Service.

Summary of Contents for TRAVEL'R ADJUSTABLE PITCH

















































Reviews:

No comments