Carefree of Colorado
Service Manual
M
IRAGE
052979-301r16
5
P
ROGRAMMING THE
R
EMOTE
R
ECEIVER
(D
IRECT
R
ESPONSE
)
Early transmitters & receivers operate on a frequency of 418MHz. Models for
2007 & on operate on 433MHz. The transmitter and receiver frequencies must
match. Identifying the transmitter frequency is described under the operational
notes below.
1. Power to the control box must be on.
2. Press and release the “Press to Learn Transmitter” button on the bottom of the
receiver box. The receiver is in program mode when the red light comes on.
3.
For Gray Button Key FOBS:
Press and release
ANY
button on the remote.
It is recommended to use the
STOP
button. The red light will go out after
the receiver learns the remote signal.
CAUTION
W
HEN THE RECEIVER LEARNS THE TRANSMITTER SIGNAL THE SYSTEM WILL
PERFORM THE OPERATION OF THE BUTTON PRESSED
.
E
XAMPLE
:
P
RESSING AN
"E
XTEND
"
BUTTON DURING THE
LEARNING PHASE WILL CAUSE THE AWNING TO EXTEND WHEN THE RECEIVER LEARNS THE SIGNAL
.
U
SE CAUTION
TO AVOID UNEXPECTED MOVEMENT BY THE AWNING
.
4.
For Key FOBS w/ Antenna:
Press and release the
STOP
button on the remote. The red light will go out after
the receiver learns the remote signal.
NOTE: Pressing the stop button will cause the blue up arrow button to default as the open
(extend) function.
If a function button is pressed to train the receiver, it will be programmed as the open
(extend) button. Example: Pressing the bottom button will program the bottom button
for extend and the top button as retract.
5. Repeat for each additional remote.
Operational Notes:
a. Transmitter and receiver must match in
frequency (418 MHz or 433 MHz).
Key FOBs:
The gray button Key FOBS are
marked with a label for 418MHz or
433MHz.
Key FOBS w/ antenna are 433MHz.
Receivers:
418 MHz receivers are marked
"RR24".
433 MHz receivers marked "RR"
Version 1 can only be used with the
433 MHz gray button Key FOB.
433 MHz receivers marked "RR"
Version 2 can be used with either of
the 433 MHz Key FOBs.
If replacing the remote receiver, version 5 is compatible with 433MHz key fobs versions 2 thru 5. If the key
fob is an older version, it will be necessary to replace the key FOB.
b. The receiver exits the program mode after ten seconds.
c. If the light does not come on above, the memory is full and must be cleared.
d. If the light does not go out above, the receiver already knows the transmitter's signal or the battery in the
remote needs to be replaced.
e. To clear the memory:
PRESS AND HOLD
the transmitter learn button. While holding the button, the indicator light
should be OFF for the full 5 seconds then come on.
f. The system may be programmed for up to 5 remotes. Additional remotes may be ordered separately.
DR020
TO
EYE POR
T
on RP24
Program
Mode
Press to Learn
T
ransmitter
UP
Program
Button
Indicator
Light
418 MHz
433 MHz
Versions 2-5
FCC ID OJM-CMD-KEYX-XXX
315MHz
418MHz
433MHz
FCC ID OJM-CMD-KEYX-XXX
315MHz
418MHz
433MHz
433 MHz
or
TO
EYE POR
T
on RP24
Program
Mode
Press to Learn
T
ransmitter
UP
RR24
TO
EYE POR
T
on RP24
Program
Mode
Press to Learn
T
ransmitter
UP
RR
RR24
RR
Version 1
RF Receiver
DR026a
TO
EYE POR
T
on RP24
Program
Mode
Press to Learn
T
ransmitter
UP
RR
RR
Version 5
Rear Label
ONL
Y
ONL
Y
418 MHz
433 MHz
433 MHz
