manualshive.com logo in svg

Carefree Freedom WM, Service Manual

Share
Download
Carefree Freedom WM Service Manual Download Page 18

F

REEOM 

WM Service 

Manual 

Carefree of Colorado

 

14 

052563-301r5 

O

PTIONAL 

LED

 

L

IGHTING

 

Optional LED lighting may be mounted in the lead rail.  The wiring runs along the top of the arm. 

For motorized awnings:

  Route the LED wire harness with the motor cable. 

For manual crank awnings:

  The harness is routed through the end of the case, then through the vehicle 

wall. 

 NOTICE

  

The wire should be secured to the wall of the vehicle where it is exposed on the outside of 

the vehicle.  Use a quality silicone sealant/adhesive. 

 NOTICE

   

Do not route the wire over sharp edges or heat sources that can cut or fray the wires or 

wire insulation. 

Damage that is a result of improper routing may void warranty. 

S

WITCH 

I

NSTALLATION

 

NOTE:  

Installers may

 

choose to furnish the control switch.  The installation requires that the power line 

(+12VDC) be attached to a dedicated 2A circuit breaker or a 2A in-line fuse must be installed between the 
switch and power source.  For easy access, locate the fuse close to the switch. 

1.  Determine the location of the switch. 

2.  At the switch location, cut a 1 1/8" x 1 

1/2" hole. 

3.  Wire the switch as shown below.  Wire 

terminals at the switch are .187, 18-24 
awg female disconnects. 

NOTE:  

Allow adequate slack in the 

12VDC power line so that the in-line fuse 
(installed in step 4) can be accessed from 
behind the switch. 

4.  Install the in-line fuse: 

4.1. 

Near the switch, cut the red 
12VDC power line to the switch.  
Do not strip the insulation. 

4.2. Insert a wire end into one of the 

wire channels until it butts up 
against the stop. 

4.3. Fold that half of the connector 

body over until the element 
contacts the wire.  Use pliers to 
crimp the connector closed. 

4.4. Repeat for the second wire end. 
4.5. Slide the fuse into the fuse port.  

Ensure that is firmly seated. 

5.  Press the in-line fuse, wires and switch 

into the mounting hole.  Secure the 
switch using two (2) #6 x 1/2" screws. 

6.  Snap the switch bezel over the switch 

frame. 

LED002c

 Vehicle Wall

Red

+12VDC

GND

Single Pole

Single Throw Switch

18awg Wire

(minimum)

Connector at

Lead Rail

LED Strip in Lead Rail

Red

Black

Wire Routed
in Arm

18-24awg
Female Disconnect (x2)

ON

OFF

1.13"

1.5"

1.88"

2.9"

#6 x 1/2” Screw (x2)

2A In-line Fuse

2A In-line Fuse

(+12VDC Line)

Summary of Contents for Freedom WM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands