manualshive.com logo in svg

Carefree Freedom WM, Service Manual

Share
Download
Carefree Freedom WM Service Manual Download Page 12

F

REEOM 

WM Service 

Manual 

Carefree of Colorado

 

8 

052563-301r5 

R

EPLACING THE 

L

EAD 

R

AIL 

C

ONNECTOR

 

1.  Remove the arm according to the instructions on page 7. 

2.  Remove the lead rail end plate. 

3. Carefully measure and mark the location of the existing 

connector and ramp. 

4.  Loosen the securing screw and slide the existing connector 

from the lead rail. 

5.  Insert the new connector assembly into the lead rail and position at the marks made previously. 

 NOTICE

  

Failure to position the connector correctly can cause the arm and lead rail to not close 

properly. 

6.  Tighten the outer securing screw. 

7.  Attach the lead rail end plate. 

8.  Return to Replacing the Arm on page 7. 

R

EPLACING THE 

C

ASE 

C

ONNECTOR

 

1.  Remove the arm according to the instructions on page 7. 

2.  Carefully measure and mark the location of the existing connector. 

3.  Loosen the clamping screw then slide the wedge from the housing.  Lift 

both parts from the case. 

4.  Remove the knuckle and bolt from the new connector and separate the 

new wedge and new housing. 

5.  Slide the housing into the upper channel of the case and the wedge 

into the lower channel of the case. 

6.  Slide the wedge into the housing and position the housing at the marks 

made previously.  Tighten the clamping screw to 25-30 in-lbs. 

 NOTICE

   

Failure to position the connector correctly can cause 

the arm and lead rail to not close properly. 

7.  Return to Replacing the Arm on page 7. 

P

ITCH 

A

DJUSTMENT 

–

 

F

REEDOM 

WM 

The Freedom WM provides minor pitch adjustment for aligning the lead rail with the case.  This adjustment 
is only for fine-tuning the installation.  It is not intended as an operational pitch adjustment. 

 NOTICE

   

When the pitch of the awning is adjusted, it is 

important that the lead rail is parallel to the awning housing. 

1.  Open the awning to access the adjustment screw located on 

the arm case knuckle. 

2.  Have a second person lift up on the lead rail to relieve the 

pressure on the adjustment screw. 

3.  Using a 5mm allen wrench, turn the adjustment screw clockwise 

to raise the lead rail; turn the adjustment screw counterclockwise 
to lower the lead rail. 

4.  Repeat for the other side as necessary. 

WM013

Raise

Lower

Pitch Adjustment Screw

Arm Case Knuckle

 

Figure 7.  Pitch Adjustment. 

 

Remove

End Plate

Ramp

Arm

Connector

WM039

Wedge

Housing

Clamping
Screw

WM038

Case Connector

Housing

Summary of Contents for Freedom WM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands