Carefree FREEDOM FREESTYLE WM Service Manual Download Page 20

Page: 20 / 24

REEDOM

REESTYLE

WM Service

Manual

Carefree of Colorado

052573-301r8

LECTRICAL

IRING

CHEMATIC

EPLACING THE

IRECT

ESPONSE

ODULE

The Direct Response Module is located on the LH side (motor side) of the lead rail.

NOTE:

The Freestyle awning will not operate electrically when the module is disconnected.

To Remove:

1. Disconnect power to the awning.

2. Remove the two screws holding the module. Pull the module

from the lead rail.

NOTE:

The mounting brackets are held in place by tension from

the screws. When the screws are removed, the bracket will sit
loosely in the lead rail. Use care save the brackets.

3. Detach the quick release connectors.

4. Set the module aside.

To Install:

1. Connect the wires. Make sure to match wire color and size when making connections.

2. Position

the

bracket.

3. Tuck the wires and connectors behind the module and attach the module with the two screws removed

previously.

FF001a

On/Off

Rear View of

Switch Assy

Control Module

(mounted in

lead rail)

Gray

Yellow

Brown

Red

Black

Red

Black

Awning

Brown

Blue

(Retract)

(Common)

(Extend)

(+12Vdc)

(Ground)

Chassis Ground

.25, 14-16awg

Spade Terminals

1 Male, 1 Female

+12VDC

.187, 14-16awg
Female Spade
Terminals (x2)

.187, 18-20awg

Female Spade

Terminals (x3)

Additional

Extend/Retract

Switch

Gray

Yellow

Brown

Extend/

Retract

Blue

Brown

Red Shrinkwrap

Black Shrinkwrap

Red

18awg Wire

(minimum)

LED Strip in Lead Rail

2A In-line Fuse

Red
Black

+12VDC

Chassis Ground

Module Harness

(Routed on Top of Arm)

(+12Vdc)

(Ground)

LED Switch

See Below

Red

+12VDC

Single Pole, Single Throw Switch

18awg Wire

(minimum)

Red (from power harness)

18-24awg
Female Disconnect (x2)

2A In-line Fuse

GND

Red

+12VDC

Lighted Single Throw Switch

18awg Wire

(minimum)

Red (from power harness)

2A In-line Fuse

18-24awg

Female Disconnect (x2)

FF018

Direct Response
Module

Quick Disconnects

Summary of Contents for FREEDOM FREESTYLE WM

























Search results

Summary of Contents for FREEDOM FREESTYLE WM

Reviews:

Related manuals for FREEDOM FREESTYLE WM

Brands by name

Popular brands

Carefree FREEDOM FREESTYLE WM, Service Manual

Search results

Summary of Contents for FREEDOM FREESTYLE WM

Reviews:

Related manuals for FREEDOM FREESTYLE WM

Brands by name

Popular brands