background image

M

ANUAL 

P

ATIO 

A

WNING

 

Installation Manual 

Carefree of Colorado

 

052876-005r3 

F

ACTORY 

I

NSTALLED 

LED

(O

PTIONAL

S

PECIFICATIONS

 

Mounting 
Options: 

a)  LED light strip is mounted in the roller tube.  The power harness is concealed in the canopy hem. 

b) 

LED light strip is mounted at the awning rail.  Requires special canopy with integrated strip holder.

 

Length: 

Available for awnings 10' – 21' 

Power: 

1A, 12Vdc 

Color: 

Bright White  6000K (standard) 

Control: 

Single pole, single throw switch (SR0101) 

Note:  For an installer furnished switch, see notes in "Switch Installation" on page 7 

NOTICE

  

The following information must be followed to avoid damage to the wiring during and 

after installation.

 

a)  The wire should be secured to the wall of the vehicle where it is exposed on the outside of the vehicle.  

Use a quality silicone sealant/adhesive. 

b)  Do not route the wire over sharp edges or heat sources that can damage the wires or wire insulation. 
c)  Damage that is a result of improper routing may void warranty. 

W

HITE 

LED

 

S

CHEMATIC AND 

L

AYOUT

 

 

H

ARNESS 

R

OUTING INTO THE 

V

EHICLE

 

1.  Drill a 3/16" hole into the vehicle wall below the right edge of the canopy. 

2.  Route the wires from the canopy into the vehicle.  Allow slack in the wire between the canopy and the 

wall.  Seal the hole and wires with a quality silicone sealant. 

3.  Attach excess wires and connectors (for awning rail applications) along the bottom of the awning rail 

using a quality silicone sealant. 

NOTE:   

There  is  approximately  8  feet  of  wire  from  the  wall  entry  point.    Controls  should  be  located 

within this distance. 

LED002a

LED Strip

 Vehicle Wall

Red

+12VDC

GND

Single Pole

Single Throw Switch

18awg Wire

(minimum)

Red Black

18-24awg

Female Disconnect (x2)

2A In-line Fuse

Power Harness

LED Holder

at Awning Rail

Roller Tube Mount

LED Strip

in LED Slot

Power Harness

Sewn in Canopy Hem

3/16" Hole

Route Wire With Slack

Between Canopy and Wall

Attach Wires Along

Bottom of Awning Rail

Canopy Harness

Awning Rail LED

3/16" Hole

Summary of Contents for FIESTA










Reviews: