16
FONCTIONS DE LA CARTE LOGIQUE
Nomenclature
PR: Touche de programmation
LPR: Led de programmation
D1: Dip-switch sélection fonctions
Leds témoins: TB-FTCS-FTCI
État de fonctionnement des dispositifs
de sécurité.
Leds allumées:
dispositifs de sécurité en état de veille
(ou court-circuités s'ils ne sont pas
utilisés).
Leds éteintes:
dispositifs de sécurité en panne, en
phase d'intervention ou court-circuités
s'ils ne sont pas utilisés.
FONCTIONS DE LA CARTE LOGIQUE EXTRACTIBLE
1) Temps de travail
0-120 secondes
La porte est considérée comme étant complètement ouverte (donc, la refermeture s'effectuera automatiquement)
même si le temps d'ouverture s'est écoulé et le fin de course
FCA
n'a pas été activé; programmer un temps d’ouver-
ture de façon à toujours avoir une marge de temps en plus par rapport à l’arrivée de la porte au fin de course
FCA
.
2) Temps d'arrêt
0-120 secondes
Régler le temps d’arrêt en fonction des caractéristiques du moteur; si ce temps est très court, dès que la porte
atteint la position d’ouverture complète, la refermeture se déclenche immédiatement.
SÉLECTION À TRAVERS DIP-SWITCHES (D1)
DIP 1: On => refermeture automatique validée.
Off => refermeture automatique invalidée.
DIP 2: On => mode de fonctionnement manuel activé.
Off => mode de fonctionnement manuel désactivé.
DIP 3: On => modalité
TD
: “ouverture-fermeture” avec inversion seulement en phase de fermeture.
Off => modalité
TD
: “ouverture-blocage-fermeture-blocage”.
NOTA: pour la configuration des dip-switches: mettre le programmateur hors tension, régler les dip-switches et
remettre ensuite le programmateur sous tension.
PROGRAMMATION DES TEMPS DE TRAVAIL (OUVERTURE PARTIELLE, OUVERTURE ET ARRÊT)
1) Avec porte complètement fermée, garder appuyée la touche
“PR”
pendant 4 secondes: la LED
“LPR”
doit rester
éteinte quelques instants avant de commencer à clignoter rapidement pour signaler l'accès à la programmation.
La lampe témoin clignote de la même façon que la LED. Relâcher la touche
“PR”
.
NOTA: si à une pression sur la touche
“PR”
, la LED
“LPR”
s’allume tout de suite et reste allumée en continu, le
programmateur ne se trouve pas en condition de fermeture complète, d’où l’impossibilité d’accéder à la program-
mation; couper et remettre le courant au programmateur.
Si à une pression sur la touche
“PR”
, la LED
“LPR”
se met à clignoter, il y a une erreur au niveau des données
mémorisées: le programmateur se bloque et il faudra programmer de nouveau les temps (voir paragraphe “Signa-
lisations d’alarme”
Si les dispositifs de sécurité (
TB, FTCI
et
FTCS
) ne sont pas en état de veille ou si le fin de course en ouverture
s’avère activé, la programmation des temps n’est pas faisable.
6
3 2 1
ON
LPR
FTCI FTCS TB
PR
TCS
PR
CS1112B.01
D1
Logica PRG401 (cs1112AB.01)
YPR302
05-03-2001
DC0325
Description:
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law