Cardin Elettronica 200/BL3924ERB Instruction Manual Download Page 18

Page: 18 / 52

• After having installed the device, and

before powering up the pro-

grammer

, release the door (manual release mechanism) and move it

manually, checking that it moves smoothly and has no unusual points
of resistance.

• The controlled load output (binding post 15) is aimed at reducing
battery power consumption (if they are installed) during blackouts;
photocells and other safety devices should be connected to this output.

• When a command is received, via radio or via wire, the electronic pro-
grammer routes voltage to the

CTRL 30 Vdc

output. It then evaluates the

state of the safety devices and if they are at rest it will activate the motor.

• Connecting devices to the controlled output contact also allows you to
carry out the autotest function (enabled using DIPs 7 and 8) and check
that the safety devices are functioning correctly.

• The presence of the electrical current sensor does not dispense with
the obligation to install photoelectric cells and other safety devices
foreseen by the

safety standards in force

• Before connecting the appliance make sure that the voltage and
frequency rated on the data plate conform to those of the mains supply.

• For the

230 Vac

power supply only use a

2 x 1.5 mm

+ cable.

• The cable may only be replaced by qualified technicians.

• An all pole trip switch with at least

3 mm

between the contacts must

be installed between the unit and the mains supply.

• Don't use cables with aluminium conductors; don't solder the ends
of cables which are to be inserted into the binding posts; use cables
marked

T min 85°C

and resistant to atmospheric agents.

• The terminal wires must be positioned in such a way that both the
wire and the insulating sheath are tightly fastened (a plastic jubilee clip
is sufficient).

230 Vac POWER SUPPLY CONNECTION

• Connect the control and security device wires.
• Run the mains power supply to the

separate

two-way

terminal board that is already

connected to the transformer.
• The master motor "

" and relative encoder are prewired. If you need to dis-

connect them (for maintenance interventions etc.) you must replace the cable
following the colour order of the wires as shown in figure 12.

Preparing the motor connection wires

• The

kit

contains

10 metres

of 6-wire cable that should be cut according to the

needs of the installation:

- connect the wires of motor "

" and encoder "

" to the wiring board of the

slave motor (second motor);

- you must scrupulously respect the motor connection sequence between the

motors and the programmer. The order of the binding post connections 1 to 6
is identical on both;

- run the end of the cable to the terminal board on the master motor and connect

it to the wiring board.

Note: If you need to choose a longer cable for particular installations (cut from the
100 metres of cable supplied in a reel) you must remember that in order to avoid
current dispersion the maximum length of the cable must not exceed

20 metres

Motor 1

1-2

Motor power supply 1

3-4-5-6

Encoder signal input 1

Motor 2

1-2

Motor power supply 2

3-4-5-6

Encoder signal input 2

• Fasten the geared motor (fig. 8) to the base plate using the screws "

" and self-

locking nuts.

• Connect the power, safety device and the second motor/encoder "

" to the

electronics card (fig. 9).

• Insert the operator arm "

" onto the motor drive shaft as indicated in fig. 2 and

tighten down using the supplied screw and washer "

• Carry on with the assembly according to the type of operator arm:

•

206/BL3924ARM - 206/BL3924SRM (ﬁg. 2)

insert the plastic ferrules "

" into the holes on the curved arm "

Det. A-B

", con-

nect the curved arm "

" to the straight arm "

" and to the bracket "

" using the

screws "

" and self-locking nuts "

" after having inserted the zinc-plated spacer

" inside the plastic ferrule "

• Release the motor (fig. 9, Det "1") by rotating the hexagonal key clockwise until

the motor has been released.

• Fasten the front bracket to the gate using two

screws (fig. 4). The position

of the front bracket is determined by opening the arm to its maximum extension
(with the gate fully closed) and aligning the points 1,2 and 3 (fig. 4). Next, move
point 3 backwards by

100 mm

from the point of alignment. The arm must be in

square "

" (fig. 5).

•

206/BL3924DRM

To install the straight arm with guide follow detail 1 in figure 2

and the dimensions in figure 5a.

Check the following:

- with the front bracket resting against the gate check that it does not suffer forcing
along the "

" axis (fig. 5) either upwards or downwards

while the gate is moving.

Should this occur either the gate or the geared motor has been incorrectly installed
and this could damage the appliance. Once you have checked all the alignments
fasten down the front bracket to the gate.

Note

: the operator arm

206/BL3924SRM

has been fitted with special self-lubricating

bearings at the joints "

"-"

" where it rotates thus allowing the arm to be inclined

leading to a play of

± 8°

on the gate (see fig. 5a) while at the same time maintaining

fluent rotation.

• After finishing the installation of the appliance and carrying out the electrical con-

nection fit the upper and lower covers:

- fit the upper cover "

" and fasten down using the screws "

" (fig. 10);

- fit the lower access cover "

" and fasten down using the supplied key "

• You are advised to fit an electric locking device on the installation (see standard

installation fig. 1).

Releasing the gate should only be carried out when the motor has stopped because
of blackouts.
To release the gate use the key supplied with the appliance "

" fig. 10.

Releasing the gate

Slide open the lower access door "

" (fig. 10), slide out the hexagonal key "

Det. 2

(fig. 10), insert it into the hole of the release mechanism and rotate it clockwise until
the motor is released. This will release the geared motor and free the gate, which can
then be opened by pushing lightly on the gate.

Locking the gate

Remove the hexagonal key, insert it into the hole of the release mechanism and rotate
it anticlockwise until the motor is blocked. Replace the hexagonal key "

" in its seat,

slide the lower access cover "

" into place and lock it. manually by pressing on the

gate or by reactivating the motor.

Electronic control unit for two dc motor with an incorporated encoder and radio
receiver card, which allows the memorisation of

300 user codes

. The "rolling code"

type decoder uses

433.92 MHz (S449)

series transmitters.

The motor rotation speed is electronically controlled, starting slowly and increasing
in speed; the speed is reduced as it nears the travel limit so as to enable a controlled
smooth stop. Programming is carried out using one button and allows you to set the
system, the current sensor and the entire gate travel distance.
The intervention of the anticrush/antidrag sensor during the closing and opening
stages causes travel direction inversion.

Attention!

There is no

230 Vac

contact on any part of the electronic

card: only low voltage safety current is available. In conformity with the
electrical safety standards it is forbidden to connect binding posts

and

directly to a circuit that receives power greater than

30 Vac/dc

Warning!

For the correct operation of the programmer the incor-

porated batteries must be in good condition: the programmer will

lose the position