background image

 

 Version 29.01.2020 

HW: CAM (V97)/ (V52)GD 

CI-RL3-MBN51 

P

a

g

e

5

 

 
1.3.

 

Connection Video-Interface 

 

The video-interface converts the connected after-market sources video signals into a digital 
RGB signal which is inserted in the factory monitor using separate trigger options. 
Furthermore, it reads vehicle’s digital signals out of the vehicle’s CAN-bus system and 
converts them for the video interface. 

 

 

 

 
 
1.4.

 

Dip-switch settings (black) 

 

Some settings must be selected by the dip-switches on the  
video-interface. Dip position down is ON and position up is OFF. 
 

 

See the following chapters for detailed information. 
 

After each Dip-switch-change a power-reset of the Interface-box has to be performed! 

 

 
 

 

Dip 

Function 

ON (down) 

OFF (up) 

No Function 

 

Set OFF 

Video 1 

enabled 

disabled 

Video 2 

enabled 

disabled 

No Function 

          

Switch to OFF 

Rear-view cam type 

After-Market 

Factory or none 

Monitor 

selection 

Try all possible combinations of dip 6, 7 and 8 to find the 

best picture (quality and size) 


Summary of Contents for CI-RL3-MBN51





















Reviews: