Instruction manual WMi3000 / WMi3005
12
Connect inlet pipe
Connect the inlet pipe as indicated in the figure.
Install inlet pipe
1. Connect the elbow to tap and fasten it clockwise.
2. Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.
NOTES:
after connection, if there is any leakage with
hose, then repeat the steps to connect inlet pipe. The
most common type of tap shall be used to supply
water. If tap is square or too big, then standard tap
shall be changed.
Hole plug
This Hole plug is used to block the hole on the back of
the washing machinet.
Place outlet hose
There are two ways to place the end of outlet hose:
1. Put it inside the sink bowl as shown
P.08
P.09
Installation
Installation
Connect the inlet pipe as indicated in the figure.
Install inlet pipe
1.Connect the elbow to tap and fasten it
clockwise.
2.Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.
Notes: after connection, if there is any leakage
with hose, then repeat the steps to connect inlet
pipe. The most common type of tap shall be
used to supply water. If tap is square or too big, then
standard tap shall be changed.
Hole plug
This Hole plug is used to block the hole on the back
of the washing machinet.
Place outlet hose
There are two ways to place the end of outlet hose:
1.Put it inside the sink bowl as shown
Unpacking the washing machine
Unpack your washing machine and check if there is any damage during the transportation. Also
make sure that all the items (as shown in Page
7
) in the attached bag are received. If there is any
damage to the washing machine during the transportation, or any item is missing, please contact
your retailer immediately.
Dispose of the packing materials
The packing materials of this machine may be dangerous to children. Please dispose of them
properly. Please dispose the related packing materials according to the relevant local
regulations. Please do no throw the packing materials away together with the other daily living
disposals.
Remove transport bolts
Before using this washing machine, transport bolts
must be removed from the backside of
this machine. Please take the following steps to
remove the bolts:
1.
Loosen all bolts with spanner and then remove them.
2.Fill
the holes with transport hole plugs.
3.
Keep the transport bolts stored away safely for future use.
Select the location
Before installing the washing machine, the location characterised as follows shall be
selected:
- Rigid, dry, and level surface (if not level, please make it level with reference to the
following figure “Adjust Leg”)
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0 C
- Keep far away from heat resources.
- Make sure that the washing machine does not stand on the power cord.
- Do not install the washing machine on the carpet floor.
Adjust Legs
1.
When positioning the washing machine, please first
check if the legs are closely attached to the washing
machine. If not, please turn them to their original
positions with hand or spanner and tighten the nuts
with spanner.
2.
After positioning the washing machine, press four
corners on top cover of washing machine in
sequence. If the washing machine is not stable
when being pressed, this leg shall be adjusted.
3.
Ensure the positioning status of washing machine. Loosen the lock nut with spanner
and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.
4.
After being locked properly, press four corners again to make sure that they have been adjusted
suitably. If it is still unstable, repeat Steps 2 and 3 until stable.
5.
Put a solid cylinder horizontally on the top cover of the washing machine from in
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.
Connect inlet pipe
P.08
P.09
Installation
Installation
Connect the inlet pipe as indicated in the figure.
Install inlet pipe
1.Connect the elbow to tap and fasten it
clockwise.
2.Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.
Notes: after connection, if there is any leakage
with hose, then repeat the steps to connect inlet
pipe. The most common type of tap shall be
used to supply water. If tap is square or too big, then
standard tap shall be changed.
Hole plug
This Hole plug is used to block the hole on the back
of the washing machinet.
Place outlet hose
There are two ways to place the end of outlet hose:
1.Put it inside the sink bowl as shown
Unpacking the washing machine
Unpack your washing machine and check if there is any damage during the transportation. Also
make sure that all the items (as shown in Page
7
) in the attached bag are received. If there is any
damage to the washing machine during the transportation, or any item is missing, please contact
your retailer immediately.
Dispose of the packing materials
The packing materials of this machine may be dangerous to children. Please dispose of them
properly. Please dispose the related packing materials according to the relevant local
regulations. Please do no throw the packing materials away together with the other daily living
disposals.
Remove transport bolts
Before using this washing machine, transport bolts
must be removed from the backside of
this machine. Please take the following steps to
remove the bolts:
1.
Loosen all bolts with spanner and then remove them.
2.Fill
the holes with transport hole plugs.
3.
Keep the transport bolts stored away safely for future use.
Select the location
Before installing the washing machine, the location characterised as follows shall be
selected:
- Rigid, dry, and level surface (if not level, please make it level with reference to the
following figure “Adjust Leg”)
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0 C
- Keep far away from heat resources.
- Make sure that the washing machine does not stand on the power cord.
- Do not install the washing machine on the carpet floor.
Adjust Legs
1.
When positioning the washing machine, please first
check if the legs are closely attached to the washing
machine. If not, please turn them to their original
positions with hand or spanner and tighten the nuts
with spanner.
2.
After positioning the washing machine, press four
corners on top cover of washing machine in
sequence. If the washing machine is not stable
when being pressed, this leg shall be adjusted.
3.
Ensure the positioning status of washing machine. Loosen the lock nut with spanner
and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.
4.
After being locked properly, press four corners again to make sure that they have been adjusted
suitably. If it is still unstable, repeat Steps 2 and 3 until stable.
5.
Put a solid cylinder horizontally on the top cover of the washing machine from in
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.
Connect inlet pipe
P.08
P.09
Installation
Installation
Connect the inlet pipe as indicated in the figure.
Install inlet pipe
1.Connect the elbow to tap and fasten it
clockwise.
2.Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.
Notes: after connection, if there is any leakage
with hose, then repeat the steps to connect inlet
pipe. The most common type of tap shall be
used to supply water. If tap is square or too big, then
standard tap shall be changed.
Hole plug
This Hole plug is used to block the hole on the back
of the washing machinet.
Place outlet hose
There are two ways to place the end of outlet hose:
1.Put it inside the sink bowl as shown
Unpacking the washing machine
Unpack your washing machine and check if there is any damage during the transportation. Also
make sure that all the items (as shown in Page
7
) in the attached bag are received. If there is any
damage to the washing machine during the transportation, or any item is missing, please contact
your retailer immediately.
Dispose of the packing materials
The packing materials of this machine may be dangerous to children. Please dispose of them
properly. Please dispose the related packing materials according to the relevant local
regulations. Please do no throw the packing materials away together with the other daily living
disposals.
Remove transport bolts
Before using this washing machine, transport bolts
must be removed from the backside of
this machine. Please take the following steps to
remove the bolts:
1.
Loosen all bolts with spanner and then remove them.
2.Fill
the holes with transport hole plugs.
3.
Keep the transport bolts stored away safely for future use.
Select the location
Before installing the washing machine, the location characterised as follows shall be
selected:
- Rigid, dry, and level surface (if not level, please make it level with reference to the
following figure “Adjust Leg”)
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0 C
- Keep far away from heat resources.
- Make sure that the washing machine does not stand on the power cord.
- Do not install the washing machine on the carpet floor.
Adjust Legs
1.
When positioning the washing machine, please first
check if the legs are closely attached to the washing
machine. If not, please turn them to their original
positions with hand or spanner and tighten the nuts
with spanner.
2.
After positioning the washing machine, press four
corners on top cover of washing machine in
sequence. If the washing machine is not stable
when being pressed, this leg shall be adjusted.
3.
Ensure the positioning status of washing machine. Loosen the lock nut with spanner
and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.
4.
After being locked properly, press four corners again to make sure that they have been adjusted
suitably. If it is still unstable, repeat Steps 2 and 3 until stable.
5.
Put a solid cylinder horizontally on the top cover of the washing machine from in
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.
Connect inlet pipe
P.08
P.09
Installation
Installation
Connect the inlet pipe as indicated in the figure.
Install inlet pipe
1.Connect the elbow to tap and fasten it
clockwise.
2.Connect the other end of inlet pipe to the inlet
valve at the backside of washing machine and
fasten the pipe tightly clockwise.
Notes: after connection, if there is any leakage
with hose, then repeat the steps to connect inlet
pipe. The most common type of tap shall be
used to supply water. If tap is square or too big, then
standard tap shall be changed.
Hole plug
This Hole plug is used to block the hole on the back
of the washing machinet.
Place outlet hose
There are two ways to place the end of outlet hose:
1.Put it inside the sink bowl as shown
Unpacking the washing machine
Unpack your washing machine and check if there is any damage during the transportation. Also
make sure that all the items (as shown in Page
7
) in the attached bag are received. If there is any
damage to the washing machine during the transportation, or any item is missing, please contact
your retailer immediately.
Dispose of the packing materials
The packing materials of this machine may be dangerous to children. Please dispose of them
properly. Please dispose the related packing materials according to the relevant local
regulations. Please do no throw the packing materials away together with the other daily living
disposals.
Remove transport bolts
Before using this washing machine, transport bolts
must be removed from the backside of
this machine. Please take the following steps to
remove the bolts:
1.
Loosen all bolts with spanner and then remove them.
2.Fill
the holes with transport hole plugs.
3.
Keep the transport bolts stored away safely for future use.
Select the location
Before installing the washing machine, the location characterised as follows shall be
selected:
- Rigid, dry, and level surface (if not level, please make it level with reference to the
following figure “Adjust Leg”)
- Avoid direct sunlight
- Sufficient ventilation
- Room temperature is above 0 C
- Keep far away from heat resources.
- Make sure that the washing machine does not stand on the power cord.
- Do not install the washing machine on the carpet floor.
Adjust Legs
1.
When positioning the washing machine, please first
check if the legs are closely attached to the washing
machine. If not, please turn them to their original
positions with hand or spanner and tighten the nuts
with spanner.
2.
After positioning the washing machine, press four
corners on top cover of washing machine in
sequence. If the washing machine is not stable
when being pressed, this leg shall be adjusted.
3.
Ensure the positioning status of washing machine. Loosen the lock nut with spanner
and turn the leg with hand until it closely contacts with the floor. Press the leg with one hand and
fasten the nut closely to the washing machine with the other hand.
4.
After being locked properly, press four corners again to make sure that they have been adjusted
suitably. If it is still unstable, repeat Steps 2 and 3 until stable.
5.
Put a solid cylinder horizontally on the top cover of the washing machine from in
the left, right, front and back directions. If the cylinder keeps stable, the washing machine is
positioned level. If it rolls, the washing machine is not level. The rolling direction is the direction of
lower ground surface. Then, the two legs in this direction shall be raised at the same time until the
washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against the
ground and the nuts shall be locked tightly.
Connect inlet pipe
