manualshive.com logo in svg

Caple PH501E, Instruction Manual, Page: 4 / 16

Share
Download
Caple PH501E Instruction Manual Download Page 4

Instruction manual PH501E

Please keep this instruction manual for future reference

4

WARNINGS

 

-

It is dangerous to alter or modify the specifications of the 

appliance in any way.

 

-

This product is not designed for commercial use, it is a 

household appliance only. It is not intended to be used in:

 

-

Staff kitchen areas in shops, offices and other working 

environments.

 

-

Bed and breakfast type environments.

 

-

By clients in hotels, motels and other residential type 

environments.

 

-

Ensure that the supply cord is not wedged during the 

installation. If the supply cord is damaged, it must 

be replaced by a Caple service technician or similarly 

qualified persons in order to prevent a hazard.

 

-

Do not use harsh abrasive cleaners or sharp metal 

scrapers to clean the grille, as this may damage or 

scratch the surface.

 

-

Ensure the appliance is switched off before any cleaning 

or maintenance. 

 

-

A Caple approved engineer or highly competent 

person(s) should be used for other maintenance 

requirements.

PH501E Instruction manual.indd   4

16/07/2018   13:44

Summary of Contents for PH501E

















Reviews:

No comments