Caple DI651 Instruction Manual Download Page 42

Page: 42 / 52

Instruction manual Di651

Please keep this instruction manual for future reference

CONNECT THE AQUASTOP SAFETY SUPPLY HOSE

The appliance must be connected to the water mains using new hose-sets. The old
hose-sets should not be reused. Water pressure must be between 0,04 MPa and
1 MPa. If the pressure is below the minimum consult our Service Department for
advice.

- Pull The safety supply hoses completely out from

storage compartment located at rear of dishwasher.

- Tighter the screws of the safety supply hose to the

faucet with thread ¾inch.

- Turn water fully on before starting the dishwasher.

ABOUT THE SAFETY SUPPLY HOSE

The safety supply hose consists of the double walls. The hose’s system guarantees
its intervention by blocking the flow of water in case of the supply hose breaking
and when the air space between the supply hose itself and the outer corrugated
hose is full of water.

WARNING:

Ensure the Aquastop safety supply unit is in a vertical position once installed.

HOW TO CONNECT THE SAFETY SUPPLY HOSE

- Turn off the water.

- Unscrew The safety 2 supply hose from the faucet.

COLD WATER CONNECTION

Connect the cold water supply hose to a threaded 3/4(inch) connector and make
sure that it is fastened tightly in place. If the water pipes are new or have not been
used for an extended period of time, let the water run to make sure that the water
is clear and free of impurities. If this precaution is not taken, there is a risk that the
water inlet can get blocked and damage the appliance.

WARNING:

Please close the hydrant after using.

The content of this manual is very helpful to the users.

After installation, please make sure to keep this manual.

The

following

things

should

checked

before

starting

the

dishwasher.

The

dishwasher

level

and

fixed

properly

The

inlet

valve

open

There

leakage

the

connection

points

The

wires

are

tightly

connected

The

power

switched

The

inlet

and

drain

hoses

are

not

knotted

All packing materials and printings should be taken out from the dishwasher

Please close the hydrant after using.

Ensure the Aquastop safety supply unit is in a vertical position once installed.

Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.

Turn water fully on before starting the dishwasher.

Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.

The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the flow of water

in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated hose is full

of water.

Turn off the water.

Unscrew The safety supply hose from the faucet..

Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.

If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the

water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and

damage the appliance.

The appliance must be connected to the water mains using new hose-sets.

The old hose-sets should not be reused.

Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below the minimum

consult our Service Department for advice.

Positioning

the

Appliance

Position

the

appliance

the

desired

location.

The

back

should

rest

against

the

wall

behind

it,

and

the

sides,

along

the

adjacent

cabinets

walls.

The

dishwasher

equipped

with

water

supply

and

drain

hoses

that

can

positioned

either

the

right

the

left

sides

facilitate

proper

installation.

How

Drain

Excess

Water

From

Hoses

the

sink

waste

more than

1000

from

the

floor,

the

excess

water

hoses

cannot

drained

directly

into

the

sink.

will

necessary

drain

excess

water

from

hoses

into

bowl

suitable

container

that

held

outside

and

lower

than

the

sink.

Water

Outlet

Connect

the

water

drain

hose.

The

drain

hose

must

correctly

fitted

avoid

water

leaks.

Ensure

that

the

water

inlet

hose

not

kinked

squashed.

Extension

Hose

you

need

drain

hose

extension,

make

sure

use

similar

drain

hose.

must

longer

than

metres;

otherwise

the

cleaning

effect

iveness

the

dishwasher

could

reduced.

Syphon

Connection

Insert

the

drain

hose

into

drain

pipe

with

minimum

diameter

40mm,

let

run

into

the

sink,

making

sure

avoid

bending

crimping

it.

The

top

the

hose

must

less

than

1000mm

from the floor

How to connect the Aquastop safety supply hose

ATTENTION

After installation, please make sure to keep this manual

The content of this manual is very helpful to the users

Di651 Intergrated Dishwasher.indd 42

08/02/2017 12:59

Summary of Contents for DI651





















































Search results

Summary of Contents for DI651

Reviews:

Related manuals for DI651

Brands by name

Popular brands

Caple DI651, Instruction Manual

Search results

Summary of Contents for DI651

Reviews:

Related manuals for DI651

Brands by name

Popular brands