manualshive.com logo in svg

Capelec EOBD, User Manual

Share
Download
Capelec EOBD User Manual Download Page 67

 

23/04/2019 

 

Rev 3  

64 

V.9.

 

OPTION: 

This sub-menu is dedicated to persons in charge of installing new functions. It is secured by a 5-
digit code. 

Select the configuration menu in order to install a new feature. 

 

 

 

 

This windows shows all the functions and options already installed. 

 

V.10.Parameters by default : 

WARNING:  This  window  has  to  be  used  with  caution  because  it  allows  resetting  all  the 
configuration values. 

 

V.11.PC keyboard 

Declare here whether the virtual or physical keyboard will be used. 

 Programming « absent keyboard » means the operator will preferably use the virtual keyboard. 

 

V.12.Info Maintenance 

This menu access is secured by a maintenance code. 

It  is  possible  here  to  fill  in  the  information  about  the  maintenance  company,  to  add  a  logo  but 
also to set the commissioning date. 

At the moment of 1st programming, the commissioning date key is active (green). Then, once this 
information filled in, it will become inactive in order to make it impossible to be changed. 

 

 

Summary of Contents for EOBD






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands