background image

 

- 4 - 

IMPORTANT PRECAUTIONS 

WARNING: 

To reduce the risk of serious injury, read the following important 

precautions before using the gym. 

 

1.Read all instructions in this manual and all 

warnings on the gym before using the gym. 
Use the gym only as described in this 
manual. 

 
2. It is the responsibility of the owner to ensure 

that all users of the gym are adequately 
informed of all precautions. 

 
3. The gym is intended for home use only. Do 

not use the gym in any commercial, rental, or 
institutional settings. 

 
4. Keep the gym indoors, away from moisture 

and dust. Place the gym on a level surface, 
with a mat beneath it to protect the floor or 
carpet. Make sure that there is enough 
clearance around the gym to mount, 
dismount, and use the gym. 

 
5. Inspect and properly tighten all parts 

regularly. Replace any worn parts 
immediately prior to use. 

 
6. Keep children under the age of 12 and pets 

away from the gym at all times. 

 
7. Keep hands and feet away from moving 

parts. 

 
8. Always wear athletic shoes for foot 

protection while exercising. 

 

9. The Home Gym is designed to support a 

maximum user weight of 250 lbs pounds. 

 
10. When you are using the leg developer, 

seated row make sure to check that all 
moving parts are unhindered and 
connected properly 

 
11. When adjusting the height of the seat make 

sure that pop-pin is securely screwed in   

 
12. If you feel pain or dizziness at any time 

while exercising, stop immediately and 
begin cooling down. 

 
13. Always have someone present to ensure 

your safety when using this gym. 

 

WARNING: 

Before beginning this or any exercise program, consult your physician. 

This is especially important for persons over the age of 35 or persons with pre-existing health 

problems. Read all instructions before using. CAP Barbell assumes no responsibility for personal 

injury or property damage sustained by or through the use of this product. 

 

 

 

Summary of Contents for FM-CSH1006




















Reviews: