CanyCom CMX 252 Operator'S Manual Download Page 82

Page: 82 / 94

-73-

Maintenance

5332M-0509-020E

Main Fuse

Fuse Case

Cap

Lights Fuse

1.  Open engine hood.
2.  Push reset button to reset circuit breaker.
3.   Close engine hood.

Fuse Case

5341M-0509-030E

Resetting Circuit Breaker

1. Open engine hood.
2. Open fuse case cap. Remove fuse and

visually inspect. If it is blown, replace it with
new one of the same rating.

3.   Install fuse.
4.  Install fuse case cap.
5.  Close engine hood.

5341M-0509-020E

Reset Button

• Circuit breaker protects mower deck slide

mechanism. Check this breaker when slide
mechanism does not work.

NOTE

Replacing Main/Light Fuse

1. Lift up seat.
2. Open fuse case cap. Remove fuse and

visually inspect. If it is blown, replace it with
new one of the same rating.

3.   Install fuse.
4.  Install fuse case cap.
5.  Lower seat.

Replacing Mower Deck Lift Fuse

• The fuse that protects mower deck lift

mechanism is located under the seat. Check
this fuse when lift mechanism does not
work.

NOTE

Summary of Contents for CMX 252































































































Search results

Summary of Contents for CMX 252

Reviews:

Brands by name

Popular brands

CanyCom CMX 252, Operator'S Manual

Search results

Summary of Contents for CMX 252

Reviews:

Brands by name

Popular brands