manualshive.com logo in svg

CanyCom CMX 252, Operator'S Manual

Share
Download
CanyCom CMX 252 Operator'S Manual Download Page 74

-65-

Maintenance

5

1.  Park machine on level ground.
2.   Remove left step.

5332M-0507-070E

Adjust Nut

Lock Nut

3.  Loosen lock nut
4.   Adjust with adjust nut when brak peddal is 

free so that the brake does not drag.

5.  Adjust brake so that the brake works and the 

brake pedal locks securely when brake pedal 
is locked

6.  Tighten lock nut.

Rear Brake

 •  If brake does not work even the brake pedal 

is locked, the brake shoe is worn out. Please 
contact your CANYCOM representative for 
replacement.

 • Always keep brake adjusted for maximum performance. Improperly adjusted 

brakes may result in property damage, serious injury, or death. 

Parking Brake

Front Brake (CMX253)

7.  Lock brake pedal and Inspect that the strech 

of spring is between 5mm and 8mm. If it is 
not within this range, adjust it with adjust nut.

8.   Tighten lock nut after adjustment
9.  Install left step back in place.

Spring

5332M-0507-060E

Adjust Nut

Lock Nut

NOTE

Summary of Contents for CMX 252































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands