manualshive.com logo in svg

CanyCom CM 2103, Operator'S Manual, Page: 45 / 62

Share
Download
CanyCom CM 2103 Operator'S Manual Download Page 45

Maintenance

- 39 -

Inspecting Battery

1.  Park machine on level ground.
2.  Check the electrolyte level. If it is low, remove the head 

lamp cover, and add water.

Proper battery electrolyte level: between Upper and 

Lower reference lines.

Add only distilled water to battery

7.6  Adding Water to Battery

*  Avoid battery fluid contact with skin or clothes to avoid burns from sulfuric acid.   

In case of contact, immediately remove affected clothes and clean the affected 

skin with water.  Immediately wash eyes with water if fluid enters eyes and call 

doctor.

*  Always stop engine and turn  “OFF”  the main switch before checking or removing 

the battery.

Battery

Upper

Lower

Cover

5314M-0706-010E

*  Quick charging is a method to partially recharge a battery in a short time with a 

large amount of current. This method should be used only in emergencies.  Quick 

charging will extremely shorten battery life.  After quick charging,  always fully 

recharge the battery with the normal method as soon as possible. 

*  Always remove the battery from the machine before charging it to avoid damaging 

electrical components and wiring.

*  Connect battery cables to the correct po) and negative(-) terminals.  

Reversing connections will blow the fuse and prevent charging.

*  For safety, always disconnect the negative(-) terminal first, and connect the 

po) terminal first.  Disconnecting or connecting in the opposite order may 

cause a short circuit.

*  When reinstalling the battery, connect the po) and negative(-) to their 

original positions. Avoid contact between terminals and other surrounding  

machine parts.

*  Flammable gas is generated by the battery.  Keep open flames away from battery  

to prevent explosions.

Summary of Contents for CM 2103































































Reviews:

No comments