Canvas JENSEN FHWS80031, Assembly Instructions Manual

Page: 7 / 35

12 13
IMPORTANT SAFETY INFORMATION
Product No. 085-1573-8 | Model No. FHWS80031
IMPORTANT SAFETY INFORMATION
1. 7KLV´UHWDEOHFRPHVHTXLSSHGZLWKDVWDQGDUG/3JDVKRVHDQGregulator includ-
ing the appliance side connection for a CGA No 791 Cylinder Connection Device.
7KH/3JDVKRVHDQGUHJXODWRUVXSSOLHGZLWKWKLV´UHWDEOHPXVW be used. Only a
KRVHDQGUHJXODWRUVSHFL´HGE\PDQXIDFWXUHUFDQEHXVHGIRUUHSlacement.
a. 7KH&*$1RFRQQHFWLRQLQFRUSRUDWHVDPDJQHWLFµRZOLPLWLQJ device
WKDWDFWVWROLPLWWKHµRZRIJDVLIDOHDNLVGHWHFWHGEHWZHHQWKHUHJXODWRU
and the burner valve.
b. If the burner valve is open prior to the LP gas cylinder service valve being
RSHQHGWKHFRQQHFWLRQZLOOLQWHUSUHWWKLVIUHHµRZRIJDVWREHDOHDN
c. 7KHFRQQHFWLRQVDIHW\IHDWXUHZLOOUHGXFHJDVµRZIURPWKHUHgulator to
the appliance to a minimal level.
d . Be sure that the burner control valve is closed prior to opening the LP
JDVF\OLQGHUVHUYLFHYDOYHWRHQVXUHWKDWWKHFRQQHFWLRQµRZOLPLWLQJGHYLFH
is not triggered mistakenly.
e. ,IWKHFRQQHFWLRQµRZOLPLWLQJGHYLFHLVWULJJHUHGPLVWDNHQO\ close the LP
gas cylinder service valve and the burner valve, wait 10 seconds to allow the
device to reset, open the cylinder service valve, then open the burner valve
DQGOLJKWWKH´UHSODFHDVSHUOLJKWLQJLQVWUXFWLRQV
2. Be sure to protect the hose from any hot surfaces. Serious danger may result if
the hose contacts any hot surface.
3. Regular maintenance of the hose and regulator:
a. ,QVSHFWWKHKRVHEHIRUHHDFKXVHRIWKH´UHWDEOH,IWKHKRVH shows signs
of cracks, abrasions, cuts or damage of any kind, do not operate the appli-
ance. Fix or replace the hose as required before using the appliance. For
assistance with repair or replacement of the hose, call the service centre at
1-888-670-6684. Use only replacement parts from the manufacturer.
b. Inspect the seal inside the CGA No 791 service valve on the LP gas cylin-
der when replacing the cylinder or at least once per year. If there is any
LQGLFDWLRQRIGDPDJHKDYHWKHVHDOUHSODFHGE\DFHUWL´HGJDVGHDOHUEHIRUH
operating the appliance.
4. Do not use tools to tighten the CGA No 791 connection nut onto the LP gas
F\OLQGHUVHUYLDQGWLJKWHQRQO\
5. Be careful to not cross the threads on the connection when tightening the CGA
No 791 connection onto the LP gas cylinder service valve.
6. “Leak Test” should always be performed after attaching the connection to the LP
gas cylinder service valve. (See “Checking for Leaks” section of this manual on
page 19.)
7.
For the connection of the hose and regulator to the LP tank, refer to step 6 on
page 18.
LAVA ROCKS WARNING:
1. Lava rocks may have sharp edges. Wear safety glasses and gloves when handling.
2. If changing or substituting the lava rocks with other media, use lava rocks/pumice
stones/glass shards/glass beads available from your local authoUL]HG
dealer/distributor.
3. Pour the lava rocks evenly in to the burner area (with the exception of the
screen—if applicable). The lava rocks should be 1/2 to 1" (1.2 to 2.5 cm) above the
burner.
4.
IMPORTANT:
Do not exceed a height of 1" (2.5 cm) above the burner when
placing lava rocks or other media. Ensure no media covers the igniter screen. Store
any excess lava rocks in a safe location.
5. .HHSDZD\IURPWKHXQLWIRUWKH´UVWPLQXWHVDIWHULJQLWLQJ\RXUXQLWIRUWKH´UVW
time, as lava rocks/pumice stones /glass beads could pop out and cause injury.
Should any rocks pop out, discard them.
6. Always ensure that lava rocks/pumice stones/glass shards/glass beads are
completely dry before use. Failure to do so will cause them to crack or pop.
DO NOT PLACE ANY
MEDIA ON SCREEN
HOSE AND REGULATOR ASSEMBLY AND REPLACEMENT