background image

                                                            

SmartLock

®

 UltraLite Plus 

                       

Page 15 of 16

 

                                                                  

Installation Manual

                                      

Oct 2013 • Rev. 1.6

 

Compliance statements for : 

 

 

Federal Communications Commission (FCC) 
Statement 

Note:

 This equipment has been tested and found to comply with the limits for a class B digital 

devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:  

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and receiver.  

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.  

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interferences, and (2) this device must accept 
any interferences received, including interference that may cause undesired operation.  

Complies To:  

 

 

 

Summary of Contents for SmartLock UltraLite Plus

















Reviews: