Canon PS-7000 Service Manual Download Page 41 | Manualshive

Page: 41 / 67

background image

Chapter 4 Disassembly / Assembly

4-4

Step 3-1. HDD

Take out the HDD, following the numbers given in the figure below. For the standard

configuration (with one HDD installed), skip Steps (2) to (4).

Please be careful not to lose the jumper receptacle attached to the HDD from Upgrade Kit. It is necessary for it

to be recognized as Slave HDD (the second HDD). If the HDD from Upgrade Kit is installed without the

jumper receptacle, not only the HDD is not recognized as Slave but also customer data in the HDD or the HDD

itself can be destroyed.

Jumper receptacle

«
...
39
40
41
42
43
...
»

Summary of Contents for PS-7000




































































Reviews:

No comments

Related manuals for PS-7000

Brand: Kodak Pages: 2

Film2digital MovieMaker

Brand: Wolverine Pages: 11

Brand: uranovet Pages: 2

Brand: Xerox Pages: 143

Brand: Bell and Howell Pages: 96

ESPE Lava Chairside Oral Scanner

Brand: 3M Pages: 118

Brand: POSIFLEX Pages: 122

FeverWarn FW100

Brand: MachineSense Pages: 16

Brand: Xerox Pages: 56

Brand: Xerox Pages: 68

Brand: Canmax Pages: 252

Brand: Uniden Pages: 28

Brand: Uniden Pages: 144

Brand: Pacific Image Electronics Pages: 19

Prime Film 1800

Brand: Pacific Image Electronics Pages: 22

Perfection V200 Photo

Brand: Epson Pages: 9

Brand: Epson Pages: 113

Perfection V100 Series

Brand: Epson Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands