manualshive.com logo in svg

Canon PD-704, User Manual, Page: 11 / 26

Share
Download
Canon PD-704 User Manual Download Page 11

11 

Non-Contact Displacement Sensor User’s Manual Rev 1.00 

1-4-3. 

Connecting 

- Connecting to a computer 

 

Connect the USB cable and power cable. When the DC power is turned on, the main unit is turned on. 

 

For details, see chapter “3. I/O Terminals.” 

 
- Connecting to an external device (such as a programmable controller) 

 

Connect the optional I/O cable and power cable. When the DC power is turned on, the main unit is turned on. 

 

For details, see chapter “3. I/O Terminals.” 

 
 
- Connect or disconnect the USB cable and I/O cable with the power turned off. 
- Check the direction of the connector when it is connected. 
Incorrect connection may damage connector pins or the waterproof function, resulting in a malfunction. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

When the power is turned on, the power indicator of the main unit turns on in green. 
 
 
 
 
 
 
 
 

CAUTION

 

 

 

Main unit 

Main unit 

USB cable 

Power 
cable 

Power 
cable 

I/O cable 

On 

Summary of Contents for PD-704



























Reviews:

No comments