Canon MV MVX30i Instruction Manual Download Page 148

Page: 148 / 163

148

When condensation is detected:

❍

The camcorder stops operating and the warning message “CONDENSATION HAS

BEEN DETECTED” appears for approx. 4 seconds and “

” starts flashing.

❍

If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and

“

” starts flashing. Remove the cassette immediately and leave the cassette

compartment open. Leaving the cassette in the camcorder may damage the tape.

❍

A cassette cannot be loaded when condensation is detected.

Resuming use:

❍

It takes about 1 hour until the water droplets evaporate. After the condensation

warning stops flashing, wait for 1 more hour before resuming use.

Battery Pack Handling Precautions

DANGER!

Treat the battery pack with care.

• Keep it away from fire (or it might explode).

• Do not expose the battery pack to temperature higher than 60 ºC. Do not leave

it near a heater or inside a car in hot weather.

• Do not try to disassemble or modify it.

• Do not drop or knock it.

• Do not get it wet.

❍

Charged battery packs continue to discharge naturally. Therefore, charge them on

the day of use, or the day before, to ensure a full charge.

❍

Attach the terminal cover whenever a battery pack is not in use. Contact to metallic

objects may cause a short circuit and damage the battery pack.

❍

Dirty terminals may cause a poor contact between the battery pack and the

camcorder. Wipe the terminals with a soft cloth.

❍

Since storing a charged battery pack for a long time (about 1 year) can shorten its

lifecycle or affect performance, we recommend to discharge the battery pack fully

and to store it in a dry place at temperatures no higher than 30 ˚C. If you do not

use the battery pack for long periods, charge and discharge it fully at least once a

year. If you have more than 1 battery pack, perform these precautions at the same

time for all battery packs.

❍

Although the battery pack’s operating temperature range is from 0 ˚C to 40 ˚C, the

optimal range is from 10 ˚C to 30 ˚C. At cold temperatures, performance will

temporarily decline. Warm it in your pocket before use.

❍

Replace the battery pack if the usable time after full charge diminishes substantially

at normal temperatures.

Summary of Contents for MV MVX30i




































































































































































Search results

Summary of Contents for MV MVX30i

Reviews:

Related manuals for MV MVX30i

Brands by name

Popular brands

Canon MV MVX30i, Instruction Manual

Search results

Summary of Contents for MV MVX30i

Reviews:

Related manuals for MV MVX30i

Brands by name

Popular brands