Canon MultiPASS C530 Service Manual Download Page 202

Page: 202 / 243

3-45

MultiPASS C530/C560 Chapter 3: Maintenance & Service

6.2.2 Test mode flowchart

Figure 3-21 Test Mode

[1] D-RAM

[2] CS

[4] MODEM NCU

[7] DATA SET

[6] FACULTY TEST

TEST MODE

[3] PRINT

[5] AGING TEST

[1] RELAY 1–2

[2] FREQ 1–7

[3] Not used

[4] G3 Tx 0–8

[5] DTMF Tx 0–9

✽

[6] TONE Rx

[7] Not used

[8] V34 G3 Tx

[1] MONO SYUKKEN

[2] COLOR SYUKKEN1

[3] COLOR SYUKKEN2

[4] COMMENT

[5] Not used

[6] ENDURANCE

[7] CHECKERS

[8] Not used

[9] BLACK

[1] G3 4800bps Tx

[2] REGISTRATION

[3] SENSOR

[4] ADF

[5] Not used

[6] SPEAKER

[7] OPERATION PANEL

[8] Not used

[9] LINE 1–4

See Page 3-46

See Page 3-49

See Page 3-50

See Page 3-51

See Page 3-53

See Page 3-55

See Page 3-57

[1] ADJ LED TIME

[2] CS READ

[3] DISP LED TIME

[4] REG LED TIME

[5] SHADING TEST

See Page 3-46

‘ ’ indicates that these items
are not used in the field.

✽

See Page 3-47

✽

[8] PRINTER TEST

✽

Summary of Contents for MultiPASS C530




















































































































































































































































Search results

Summary of Contents for MultiPASS C530

Reviews:

Related manuals for MultiPASS C530

Brands by name

Popular brands

Canon MultiPASS C530, Service Manual

Search results

Summary of Contents for MultiPASS C530

Reviews:

Related manuals for MultiPASS C530

Brands by name

Popular brands