Canon imageRUNNER ADVANCE C5400i II Advance Maintenance Manual Download Page 12

Page: 12 / 16

Procedure

Detail

Note

Time

Clean the Reg Roller ( inner
& outer side), Pre-Reg
Guide ( inner & outer),Reg
sensor & prism,

Clean the Duplex Feed
rollers also.



Point

Clean all areas with lint free paper moistened with
alcohol.

Clean Secondary
Transfer Roller Area

Remove the Outer Secondary Transfer Roller

Clean toner from the cavity.

Clean Feed contact guide



Point;

Make sure springs under Secondary Transfer Roller
Assembly are in correct position.

Clean the secondary transfer guide with lint free
paper moistened with alcohol.

Clean the feed contact guide with lint free paper
moistened with alcohol.

Empty the Waste
toner bottle

Check the customer’s inventory of waste toner
bottles.

With the introduction of the iRAC5500 Series
machines the waste toner container has been
designed to have a higher capacity / yield.

Check

1
min

Visual Check

5
min

Clean

1
min

Visual Check

Main

tenance

ocess

M10

Clean

2
min

Clean

iR ADV C5500 series Advance Maintenance Guide

Summary of Contents for imageRUNNER ADVANCE C5400i II

















Search results

Summary of Contents for imageRUNNER ADVANCE C5400i II

Reviews:

Related manuals for imageRUNNER ADVANCE C5400i II

Brands by name

Popular brands

Canon imageRUNNER ADVANCE C5400i II, Advance Maintenance Manual

Search results

Summary of Contents for imageRUNNER ADVANCE C5400i II

Reviews:

Related manuals for imageRUNNER ADVANCE C5400i II

Brands by name

Popular brands