Canon imageFormula DR-6010C User Manual Download

Page: 38 / 142

Chapter 3

Basic Operation

3-8

Note

For more information on placing documents,

see “Feeding in the Page Separation Mode,” on

p. 3-5

Start scanning.

The document is fed.

IMPORTANT

• When scanning multiple page documents that are fastened together, such as invoices, set

the edge that is fastened together as the leading edge.

• When you are scanning with the bypass mode, and you place several documents that are

not fastened together into the feed tray at one time, they will be fed together.

CAUTION

■

Very thin or curled documents may not feed properly. In this case, lightly press on

the leading edge of the documents as you feed them. Take care not to get your

hand caught under the roller unit, as this may cause personal injury.

■

After you finish scanning, close the document feed tray and the document eject

tray extension to prevent damage to the scanner while it is not being used.

Roller Unit

Summary of Contents for imageFormula DR-6010C















































































































































Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands

Canon imageFormula DR-6010C, User Manual

Search results

Summary of Contents for imageFormula DR-6010C

Reviews:

Related manuals for imageFormula DR-6010C

Brands by name

Popular brands