manualshive.com logo in svg

Canon imageCLASS MPC190, Basic Manual, Page: 74 / 91

Share
Download
Canon imageCLASS MPC190 Basic Manual Download Page 74

9-12

Troubleshooting

Chapter 9

COLOUR INK LOW

The ink level in the colour ink 
tank is low.

Make sure you have a new colour ink 
tank ready to replace the used one 
when it runs out. If the machine stops 
printing when copying, press 
[Resume] to continue printing. 
However, note that ink may run out. If 
print quality deteriorates or output is 
blank, replace the ink tank.

p. 8-1

COVER OPEN

You opened the inner cover 
during an operation. 

Close the inner cover.

DATA IN MEMORY
CANNOT TURN OFF

You are unable to turn the 
machine off with the [ON/OFF] 
key because the machine is 
performing an operation.

Wait until the machine has finished, 
then turn off the machine.

INK TANK CHANGED?

You opened the inner cover.

If you replaced an ink tank, press [

2

]. 

If you did not, press [

3

].

p. 8-3

INVALID KEY/SETTING

An invalid key was pressed or an 
invalid setting was selected.

Check the key or setting you want to 
enter.

LOAD PAPER
(PRESS START KEY)

The multi-purpose tray is empty. Load paper in the multi-purpose tray. 

Make sure the stack is below the 
paper limit mark (

|

t

). Then press 

[Copy/Start] or [Resume].

p. 3-8

MACHINE IN USE
CANNOT TURN OFF

You are unable to turn the 
machine off with the [ON/OFF] 
key because the machine is 
performing an operation.

Wait until the machine has finished, 
then turn off the machine.

MEMORY FULL

The machine’s memory is full 
because you tried to copy too 
many pages at once or a very 
detailed document.

Divide the document and copy each 
part separately.

PUT IN CARTRIDGE

There is no printhead installed in 
the machine.

Install the printhead.

Setup 
Sheet

WAIT COOLING

During printing, the printhead 
may have become too hot.

Allow the machine to cool down. The 
machine will resume printing when it 
has cooled down.

WASTE INK NEAR FULL

The waste ink tank is nearly full.

If <CHECK PRINTER> then appears, 

contact your local authorised Canon 
dealer or the Canon help line.

WRONG CARTRIDGE

The printhead is not installed 
correctly.

Try to reinstall the printhead. If the 
message remains in the LCD, the 
printhead may be defective. Contact 
your local authorised Canon dealer or 
the Canon help line.

Setup 
Sheet

Message

Cause 

Action

Details

Summary of Contents for imageCLASS MPC190




























































































Reviews:

No comments