Chapter 4
4-8
F-4-13
3) Turn on the host machine power.
4) Press SW103 on the finisher controller PCB.
When SW103 is pressed, the swing guide opens and
the alignment plate moves to prescribed position.
5) Place a sheet of paper between the alignment plates,
push it against the stopper, and push the rear edge of
the paper against the rear alignment plate.
If the gap between the front alignment plate and front
edge of the paper is 1 mm or greater, end staple
position adjustment and repeat staple position
adjustment after completing alignment plate
adjustment.
6) Press SW103 on the finisher controller PCB once to
staple. However, remove the
stapled paper
manually to verify the staple position because it is not
ejected.
7) Press SW103 on the finisher controller PCB once.
8) If the staple position is correct, insert a sheet of
paper between the aligning plates and
push it
against the stopper, push the far end edge of the paper
to the rear aligning plate,
and press SW103 once
(stapling action/store adjustment value) and proceed
to step 11).
9) To adjust the staple position, press SW101 or
SW102 on the finisher controller PCB and
adjust
the staple position.
When SW101 is pressed, staple position moves 0.49
mm forward.
When SW102 is pressed, staple position moves 0.49
mm backward.
10) Repeat steps 5) and 6) and check that the staple
position is adjusted correctly.
11) Turn off all bits of SW104 on the finisher
controller PCB.
12) Turn off the power of the host machine and install
the rear cover of the finisher unit.
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
A4/rear stitch
A4/front stitch
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
A4R/rear stitch
A4R/front stitch
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
LTR/rear stitch
LTR/front stitch
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
LTRR/rear stitch
LTRR/front stitch
Summary of Contents for Finisher-T1
