Canon EOS 1300D (W) Wireless Function Instruction Manual Download Page 130

Page: 130 / 144

130

Responding to Error Messages



A problem other than error 121 to 126 occurred during the
connection to the Web service.



Try connecting to the Web service again.



Is the printer performing a printing process?



Connect to the printer again after the printing process is finished.



Is another camera connected to the printer?



Connect to the printer again after the connection between the
printer and the other camera has been terminated.



Is the power of the printer on?



Connect to the printer again after turning on the printer.

127: An error has occurred

141: Printer is busy. Try connecting again.

142: Could not acquire printer information. Reconnect to

try again.

Summary of Contents for EOS 1300D (W)

















































































































































Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands

Canon EOS 1300D (W), Wireless Function Instruction Manual

Search results

Summary of Contents for EOS 1300D (W)

Reviews:

Related manuals for EOS 1300D (W)

Brands by name

Popular brands