Canon Color Bubble Jet BJC-1000 Series Service Manual Download Page 44 | Manualshive

Page: 44 / 126

background image

Part 3: Operating Instructions

BJC-1000

3-2

1.2 Printer Dimensions

The printer’s dimensions are shown below. Allow enough space for the printer to be
used with ease.
For banner printing leave a space about the size of two A4-size papers in front of the
printer. Also allow enough space at the back of the printer to set the banner paper.

· Do not place the printer in excessive heat or humidity.
· Operate the printer under the following conditions:

Ambient temperature:

5°C to 35°C

Relative humidity:

10% to 90% (no condensation)

· Do not place the printer in direct sunlight.
· Do not place the printer near a device containing a magnet or generating

a magnetic field.

· Place the printer on a level and stable surface.
· Do not place the printer in areas subject to vibration.
· Keep the printer clean.
· When moving the printer, hold both ends.

174 mm

240 mm

360 mm

160 mm

NOTE

Figure 3-2 Printer Dimensions

«
...
42
43
44
45
46
...
»

Summary of Contents for Color Bubble Jet BJC-1000 Series































































































































Reviews:

No comments

Related manuals for Color Bubble Jet BJC-1000 Series

Brand: DataCard Pages: 25

Brand: Fenix Imvico Pages: 88

Brand: olympia electronics Pages: 4

Brand: Olivetti Pages: 2

Brand: Olivetti Pages: 109

Brand: Olivetti Pages: 111

Brand: Olivetti Pages: 8

7400DT - Phaser Color LED Printer

Brand: Xerox Pages: 20

Brand: Konica Minolta Pages: 35

Brand: J&Maya Pages: 21

Brand: Tally Pages: 76

Brand: VuPoint Pages: 20

Brand: Xerox Pages: 20

Brand: Printekmobile Pages: 2

Brand: Ricoh Pages: 2

Brand: UVP Pages: 22

Brand: Xerox Pages: 85

Jetrix LXi Series

Brand: InkTec Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands