background image

Using the Scanner

25

Chapter 2

3. Scanning Documents

There are two methods of scanning documents using the DR-1210C document 
scanner. You can scan from an application, such as CapturePerfect 3.0, or you 
can use the Job function, which allows you to scan by pressing buttons on the 
operation panel, without starting up an application. 
This section describes the scanning flow of the CapturePerfect 3.0 application 
and the Job Function.
For details on how to install each application and the driver, see the Easy Start 
Guide.

Using CapturePerfect 3.0

CapturePerfect 3.0 is an ISIS-compatible application developed for Canon 
document scanners. 
CapturePerfect 3.0 includes the following modes. Select the desired scan mode 
from the scan menu to perform scanning.

• Scan Batch to File

Documents are scanned with the preset scanning conditions, and the image 
file is saved to the specified folder.

• Scan Batch to Print

Documents are scanned with the preset scanning conditions, and the scanned 
image is printed on the specified printer.

• Scan Batch to Mail

Documents are scanned with the preset scanning conditions, the e-mail 
software is started up, and the scanned image is attached to a new e-mail 
message.

• Scan 1 Page

Only one page of the document is scanned.

• Scan Job

The scanning conditions and scan mode (Scan Batch to File, Scan Batch to 
Print, or Scan Batch to Mail) are registered in advance as a job. The scan job 
can then be performed by selecting the registered job from the drop-down 
list (

c

) and pressing 

 (Scan JOB) on the toolbar (

d

). 

b

a

DR-1210C.book  Page 25  Monday, December 19, 2005  10:35 AM

Summary of Contents for 1211B002 - DR 1210C



































































































Reviews: