background image

15 

CANNON® LIMITED WARRANTY 

 

Johnson Outdoors Inc. warrants to the original purchaser that if 

the accompanying product (see exclusions below) proves to be 
defective in material or workmanship within the following warranty 
periods, Johnson Outdoors Inc. will, at its option, either repair or 
replace same without charge (but no cash refunds will be made): 

1) The boom, motor, and reels, plus all Lexan®* parts, including 

but not limited to frames and bases, will be free from defects 
in materials and workmanship, subject to normal wear and 
tear, for the original purchaser's lifetime. 

 2) All other items will have 1-year limited warranties from the 

date of original retail purchase, except THE FOLLOWING 
ITEMS THAT HAVE NO WARRANTY WHATSOEVER: boot 
covers, clothing, Dacron line, rubber bands, swivel lock pin, 
weights, and wire cable.  

  This limited warranty may be enforced only by the original 

purchaser; all subsequent purchasers acquire the product "as 
is" without any benefit of this limited warranty. Repair or 
replacement of the product as set forth in this limited warranty 
shall be the original purchaser’s sole and exclusive remedy 
and Johnson Outdoors Inc.’s sole and exclusive liability for 
breach of this warranty. 

 

EXCLUSIONS 

 This warranty does not apply in the following circumstances: 
 

• 

When the product has been connected, installed, combined, 
altered, adjusted, serviced, repaired, or handled in a manner 
other than according to the instructions furnished with the 
product 

• 

When a serial number has been effaced, altered, or removed 

• 

When any defect, problem, loss, or damage has resulted from 
any accident, misuse, negligence, carelessness, or abnormal 
use, or from any failure to provide reasonable and necessary 
maintenance in accordance with the instructions of the 
owner's manual 

 

LIMITATION AND EXCLUSION OF IMPLIED WARRANTIES AND 
CERTAIN DAMAGES 

 
 

THERE ARE NO EXPRESS WARRANTIES OTHER THAN 

THESE LIMITED WARRANTIES. JOHNSON OUTDOORS INC. 
DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL 
DAMAGES, AND IN NO EVENT SHALL ANY IMPLIED 
WARRANTIES (EXCEPT ON THE BOOM, MOTOR, REELS, AND 
ALL LEXAN®* PARTS), INCLUDING ANY IMPLIED WARRANTY OF 
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, 
EXTEND BEYOND ONE YEAR FROM THE DATE OF PURCHASE 
(AND IN THE CASE OF THE BOOT COVERS, CLOTHING, 
DACRON LINE, RUBBER BANDS, SWIVEL LOCK PIN, WEIGHTS, 
AND WIRE CABLE, JOHNSON OUTDOORS INC. DISCLAIMS ALL 
IMPLIED WARRANTIES). THIS WRITING CONSTITUTES THE 
ENTIRE AGREEMENT OF THE PARTIES WITH RESPECT TO THE 
SUBJECT MATTER HEREOF; NO WAIVER OR AMENDMENT 
SHALL BE VALID UNLESS IN WRITING SIGNED BY JOHNSON 
OUTDOORS INC.  
 
Some states do not allow limitations on how long an implied warranty 
lasts or the exclusion or limitation of consequential damages, so the 
above limitation or exclusion may not apply to you. This warranty 
gives you specific legal rights, and you may also have other rights 
that vary from state to state. 
 
* Lexan is a registered trademark of General Electric. 

CANNON

® 

SERVICE POLICY 

 

AFTER THE APPLICABLE WARRANTY PERIOD 

 
 

After the applicable warranty period, or, if one of the above 

exclusions applies, Cannon® products will be repaired for a charge of 
parts plus labor. All factory repairs, after the applicable warranty 
period, carry a 90-Day Limited Warranty, subject to the exclusions 
and limitations stated above. 
 

TO ENFORCE WARRANTY OR TO  
OBTAIN REPAIRS AFTER WARRANTY 

 
  To obtain warranty service in the U.S., the downrigger or part 
believed to be defective and the proof of original purchase (including 
the date of purchase) must be presented to a Cannon® Authorized 
Service Center or to Cannon®’s factory service center in Mankato, 
MN. Except as noted below, any charges incurred for service calls, 
transportation or shipping/freight to/from the Cannon® Authorized 
Service Center or Cannon®’s factory, labor to haul out, remove, re-
install or re-rig products for warranty service, or any similar items are 
the sole and exclusive responsibility of the purchaser. Downriggers 
purchased outside of the U.S. (or parts of such downriggers) must be 
returned prepaid with proof of purchase (including the date of 
purchase and serial number) to any Authorized Cannon® Service 
Center in the country of purchase. Warranty service can be arranged 
by contacting a Cannon® Authorized Service Center listed on the 
enclosed sheet, or by contacting the factory at 1-800-227-6433 or 
Fax 1-800-527-4464. If the necessary repairs are covered by the 
warranty, we will pay the return shipping charges to any destination 
within the United States. 
 

DO NOT 

return your Cannon

® 

downrigger or parts to your retailer. 

Your retailer is not authorized to repair or replace them. 
 
 

Major parts, such as the motor and main frame, must be returned 

to Johnson Outdoors Inc. in Mankato, Minnesota, or a Cannon

® 

Authorized Service Center, for repair or replacement. To reduce 
shipping costs, we suggest removal of loose parts such as the boom 
and rod holders. Small parts that can be easily removed such as the 
handle and/or the counter, may be removed from the downrigger and 
returned for repair or replacement. 
 

Retain your sales receipt! Proof of purchase must accompany 
product when returned. 

 

Return Address:

 

Johnson Outdoors Inc. 

 Cannon 

Division 

 121 

Power 

Drive 

 

Mankato, MN 56001 

 

FOR YOUR INFORMATION: 

 
 Serial 

No. 

 
 Date 

Purchased 

 
 

Store Where Purchased 

 

RETAIN THIS SECTION FOR YOUR RECORDS 

LIMITED WARRA

NTY 

& SERVIC


P

O

LICY

 

Summary of Contents for Uni-Troll 10





























Reviews: