Cannon CT-500 Instruction & Operation Manual Download

Page: 5 / 49

Contents

Contents ........................................................................................................................... 1

Introduction/Installation .................................................................................................... 1

Effective Temperature Range ....................................................................................................... 1

Temperature Selection ............................................................................................................. 1

Bath Description ........................................................................................................................... 2

Notes/Cautions/Warnings ............................................................................................................. 3

Safety Precautions ........................................................................................................................ 4

Temperature Fault Sensor ........................................................................................................ 4

Thermistor Detection/Cutoff .................................................................................................... 4

Bath Fluid Level Cutoff ............................................................................................................. 4

Operator Safety ........................................................................................................................ 5

Specifications .................................................................................................................... 7

Unpack & Assemble .......................................................................................................... 8

Damaged Items ............................................................................................................................ 9

Assembly ...................................................................................................................................... 9

CT-500 Motor Stirrer Installation ............................................................................................. 11

CT-600 TE Cooler and Motor-Stirrer Installation ..................................................................... 12

Final Assembly ............................................................................................................................. 15

Rear Panel Connections .......................................................................................................... 16

Inserting Viscometer Tubes/Thermometers ........................................................................ 17

Inserting Viscometer Tubes ......................................................................................................... 17

Thermometer Immersion ............................................................................................................ 17

Filling the Bath ................................................................................................................ 19

Draining the Bath ....................................................................................................................... 20

CT-500 Operation ............................................................................................................. 21

Front Panel ................................................................................................................................. 21

Turning on the CT-500 ................................................................................................................ 22

Setting the Temperature ............................................................................................................ 22

Pre-Set Temperature Selection .............................................................................................. 22

Custom Temperature Selection .............................................................................................. 24

Verifying Limit Control Operation ..................................................................................... 26

Summary of Contents for CT-500


















































Search results

Summary of Contents for CT-500

Reviews:

Related manuals for CT-500

Brands by name

Popular brands

Cannon CT-500, Instruction & Operation Manual

Search results

Summary of Contents for CT-500

Reviews:

Related manuals for CT-500

Brands by name

Popular brands