Cannon CT-500 Instruction & Operation Manual Download | Manualshive

Page: 20 / 49

background image

12

CT-500 Instruction Manual

5.

Attach the top cover, making sure all cords pass through the rear opening and down the vertical
shaft. Secure the front cover first. Use the two longer screws with toothed washers from the
Accessories Kit to secure the housing to the sides of the vertical shaft.

CT-600 TE Cooler and Motor-Stirrer Installation

This section of the installation procedure is for the CT-600 bath only.

The CT-600 is shipped with the top housing sections installed, but with the motor-stirrer and TE
cooling unit packaged separately. To complete CT- 600 installation, remove the housing sections,
install the motor-stirrer and TE cooling unit, and reassemble the housing. Follow the procedure
below to install these components.

1.

Remove the two screws securing the rear housing to the bath chassis as shown in Figure 5. Set
the screws aside.

Figure 5: Remove Top Rear Housing

2.

Loosen but DO NOT REMOVE the two top screws securing the front housing as shown in Figure
6. This will provide play for removal of the rear housing.

Figure 6: Remove Top Rear Housing

3.

Remove the rear housing by sliding it backward away from the bath.

4.

Remove the screws securing the front housing to the bath chassis.

5.

Remove the front housing.

«
...
18
19
20
21
22
...
»

Summary of Contents for CT-500


















































Reviews:

No comments

Related manuals for CT-500

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: Obdstar Pages: 10

Brand: XAG Pages: 24

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: PASCO Pages: 5

Brand: Pasco Scientific Pages: 27

Brand: PARUS Pages: 6

i-limb access hand

Brand: Össur Pages: 246

PROPRIO FOOT PSX01

Brand: Össur Pages: 374

Brand: neofeu Pages: 28

Brand: TANNER Scientific Pages: 44

WELCH LVS 600 T

Brand: Gardner Denver Pages: 68

Brand: Cooper Pages: 10

Brand: Korg Pages: 32

Brand: DeLaval Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands