8
unless they have been given supervision or instruction concerning the use by a person responsible for their
safety.
4.Children shall not play with the breast pump. Cleaning and user maintenance shall not be made by children.
5.Warning!
Use only as intended. The breast pump is not a toy. Children shall not play with the product.
6.For home use only.
7.Wash, sterilize and dry all parts of the breast pump before each use.
8.
Warning!
Before each use check for signs of damage. If you find such, do not use the product until you
remove the damage. For advice contact an authorized service center or the shop from which you bought the
product.
9.Do not use while you are pregnant. This may stimulate the birth process.
10.Never use just before falling asleep or if you are feeling drowsy.
11.If you are infected with Hepatitis A, Hepatitis B or you are HIV positive (Human Immunodeficiency Virus),
pumping breast milk does not reduce or remove the risk of transmitting the virus to your baby through breast
milk.
12. Do not attempt to remove the pump body from your breast while under vacuum. Stop the pumping and after
that with your finger detach the silicone pad from your breast.
13.If the vacuum and pressure created causes you discomfort and paid, stop using the breast pump. Place your
finger between your breast and the silicone pad and after that remove the breast pump.
14.If there is no breast milk, do not pump for more than 5 minutes.
15.Warning!
Do not drop the and do not insert any other objects into the opening or tubing.
16. Do not clean the parts of the breast pump with strong detergents
– alcohol based ones, with bleach or with
abrasive particles.
17.When the product is not used, store it away from children reach.
18.Do not leave and do not store the product in a place with very high room temperature or under direct sunlight.
19.Do not use spare parts which are not the original ones supplied by the manufacturer or importer.
20. Do not attempt to modify or repair the product by yourself when damage occurs. Instead you must contact an
authorized service or the sales agent, from whom you have purchased the breast pump.
21.Do not use accessories, which are not approved from the producer or the importer. Using such will void your
warranty.
22.Feeding teat for a newborn 0m+ is supplied with the product. It can be attached and be used on the bottle of
the breast pump.
For your
child’s safety and health
WARNING!
Always use this product with adult supervision.
Never use feeding teats as a soother.
Continuous and prolonged sucking of fluids will cause tooth decay.
Always check food temperature before feeding.
Inspect before each use and pull the feeding teat in all directions. Throw away at the first signs of damage or
weakness,
Do not leave a feeding teat in direct sunlight or heat, or leave in disinfectant
(“sterilizing solution”) for longer than
recommended, as this may weaken the teat.
Before first use place in boiling water for 5 minutes. This is to ensure hygiene.
Clean before each use.
Do not allow your children to play with small objects, or walk/ run, while using the feeding bottle.
II. PARTS
A. Silicone massage pad; B. Pump body with funnel; C. Adjuster for the suction levels (axle of the handle); D. Silicone
membrane; E. Suction adjusting pin; F. Cap of the massaging pad; G. Suction shift knob; H. Handle; I. Silicone valve; J.
Feeding bottle; K. Bottle cap; L. Feeding teat 0m+;
М. Bottle ring
III. ASSEMBLY OF THE ELECTRIC BREAST PUMP
Make sure that you have cleaned well and sterilized all the parts of the manual breast pump before starting its assembly.
Wash your hands thoroughly!
1.Step 1 - See Figure 1:
Insert the silicone massaging pad (A) into the pump body (B). Fix it tightly to the edge by pressing it
with fingers to ensure the perfect seal. Place the cover on to the massage pad (A), in order to keep the breast pump clean,
while you prepare for the suction.
Warning!
Always use the breast pump with the massage pad attached to it.
2.Step 2 - See Figure 2
: Take the silicone membrane (D) with one hand (concave side down). Insert the suction adjusting
pin (E) into the hole in the membrane bottom. It has to go through the hole of the membrane. This way, its wider end is going
to become the base of the membrane.
