- 19 -
the product may be reduced and its operation may
become noisier.
• FIXING TO THE WALL
Drill the holes
A
respecting the distances indicated
(Fig.2). Fix the appliance to the wall and align it in hori-
zontal position to the wall units. When the appliance
has been adjusted, definitely fix the hood using the
screws
A
(Fig.4). For the various installations use
screws and screw anchors suited to the type of wall
(e.g. reinforced concrete, plasterboard, etc.). If the
screws and screw anchors are provided with the prod-
uct, check that they are suitable for the type of wall on
which the hood is to be fixed.
• FIXING THE DECORATIVE TELESCOPIC FLUE -
EXTRACTOR VERSION
Arrange the electrical power supply within the dimen-
sions of the decorative flue. If your appliance must be
installed as an extractor version, make sure an air ex-
haust hole has been prepared. Adjust the width of the
support bracket of the upper flue (Fig.3). Then fix it to
the ceiling using the screws
A
(Fig.3) in such a way
that it is in line with your hood and respecting the dis-
tance from the ceiling indicated in Fig.2. Connect the
flange
C
to the air exhaust hole using a connection pipe
(Fig.4). Insert the upper flue into the lower flue and rest
above the frame. Extract the upper flue up to the bracket
and fix it with the screws
B
(Fig.3). Remove the char-
coal filters already fitted to the appliance by turning them
90° anticlockwise (Fig. 7).
• FILTERING VERSION
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting ver-
sion.
The charcoal filters are already fitted to the appliance.
USE AND MAINTENANCE
•
We recommend that the cooker hood is switched on
before any food is cooked. We also recommend that
the appliance is left running for 15 minutes after the
food is cooked, in order to thoroughly eliminate all con-
taminated air.
The effective performance of the cooker hood depends
on constant maintenance; the anti-grease filter and the
active carbon filter both require special attention.
• The anti-grease filter
is used to trap any grease par-
ticles suspended in the air, therefore is subject to satu-
ration (the time it takes for the filter to become satu-
rated depends on the way in which the appliance is
used).
- To prevent potential fire hazards, the anti-grease
filters should be washed a minimum of every 2 months
(it is possible to use the dishwasher for this task).
- After a few washes, the colour of the filters may
change. This does not mean they have to be replaced.
If the replacement and washing instructions are not fol-
lowed, the anti-grease filters may present a fire haz-
ard.
• The active carbon filters
are used to purify the air
which is released back into the room. The filters are
not washable or re-usable and must be replaced at least
once every four months. The active carbon filter satu-
ration level depends on the frequency with which the
appliance is used, the type of cooking performed and
the regularity with which the anti-grease filters are
cleaned.
• Clean the cooker hood frequently, both inside and
outside, using a cloth which has been dampened with
denatured alcohol or neutral,
non
-abrasive liquid
detergents.
• The light on the cooker hood is designed for use dur-
ing cooking and not for general room illumination. Ex-
tended use of the light reduces the average duration of
the bulb.
• COMMANDS:
(Fig.8)
LUMINOUS
the key symbols
are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
F
= AUTOMATIC STOP TIMER - 15 minutes
•
By pressing key
F
for two seconds (with the hood
switched off) the “
clean air
” function is activated. This
function switches the appliance on for ten minutes every
hour at the first speed. As soon as this function is acti-
vated the motor starts up at the first speed for ten min-
utes, During this time key
F
and key
C
must flash at the
same time. After ten minutes the motor switches off and
the LED of key
F
remains switched on with a fixed light
until the motor starts up again at the first speed after
fifty minutes and keys
F
and
C
start to flash again for
ten minutes and so on. By pressing any key for the
exclusion of the hood light the hood will return immedi-
ately to its normal functioning (e.g. if key D is pressed
the “
clean air
” function is deactivated and the motor
moves to the 2nd speed straight away. By pressing key
B
the function is deactivated).
• Active carbon/grease filter saturation:
- When button
A
flashes at a frequency of
2 seconds
,
the
grease
filters must be cleaned.
- When button
A
flashes at a frequency of
0.5 seconds
,
the
carbon
filters must be replaced.
After the clean filter has been replaced, the electronic
memory must be reset by pressing button
A
for
approximately
5 seconds
, until the light on the button
stops flashing.
•COMMANDS:
(Fig.9)
MECHANICAL
the key symbols
are explained below:
A
= LIGHT
B
= OFF
C
= SPEED I
D
= SPEED II
E
= SPEED III
G
= MOTOR WORKING indicator
•COMMANDS:
(pic.10)
SLIDER
the key symbols are
explained below:
A
= Light switch
