background image

VCO-6131E-4M2  l

User’s Manual  

4.3.12  USB Configuration

111

Chapter 4: BIOS Setup

Item 

Options 

Description 

Legacy USB Support 

Enabled

[Default] 

Disabled 

Auto 

Enables Legacy USB support. AUTO option 
disables legacy support if no USB devices are 
connected. DISABLE option will keep USB 
devices available only for EFI applications. 

XHCI Hand-off 

Enabled

[Default] 

Disabled 

This is a workaround for OSew without XHCI 
hand-off support. The XHCI ownership change 
should be claimed by XHCI driver. 

USB Mass Storage 

Driver Support 

Enabled

[Default] 

Disabled 

Enable/Disable USB Mass Storage Driver 
Support. 

USB transfer time-out

1 sec ,
5 sec ,

10 sec ,

20 sec

[Default] 

The time-out value for Control, Bulk, and 
Interrupt transfers. 

Device reset time-out 

10 sec ,

20 sec

[Default] ,

30 sec,

40 sec

USB mass storage device Start Unit command 
time-out. 

Device power-up 

delay 

Auto

[Default] 

Manual 

Maximum time the device will take before it 
properly reports itself to the Host Controller. 

‘Auto’ uses default value: for a Root port it is 

100ms, for a Hub port the delay is taken form 
Hub descriptor.

Summary of Contents for VCO-6131E-4M2


































































































































Reviews: