Canada Docks Do-It-Yourself Small Floating Hexagon Assembly Instructions Manual Download Page 8 | Manualshive

Page: 8 / 11

Canada Docks Do-It-Yourself Small Floating Hexagon Assembly Instructions Manual Download Page 8

SMALL FLOATING HEXAGON INSTRUCTIONS

Canada

Docks

.

ca

TM

Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca

26

24

25

27

28

29

Connect the floats to the dock frame with 3” Gal-

vanized Carriage Bolts (C) , D-Washers (H), Lock-

Washer (G) and Kep-Nuts (F). Install carriage bolt

assembly at locations indicated in red.

C

H

G
F

Install eyebolt assembly at the location indicated in

green.

Install eyebolt assembly at the location indicated in

green.

H

H

G

G

T

T

F

F

Place the float unto the joists below. Align the float

squarely and evenly with the dock

frame.

Ensure the float is square and evenly placed against

the joists below. Use the four slots of the float as a

template to drill four holes (use a 13/32” drill bit) into

the joists.

Position of float

slots to be drilled

Float Slot

Connect the floats to the dock frame with 3” Gal-

vanized Carriage Bolts (C) , D-Washers (H), LockWash-

er (G) and Kep-Nuts (F). Install carriage bolt

assembly at locations indicated in red.

C

H

G
F

«
...
6
7
8
9
10
...
»

Summary of Contents for Do-It-Yourself Small Floating Hexagon












Reviews:

No comments