Can-Am Spyder RT Limited SE6 Instructions Manual Download Page 46

Page: 46 / 52

SETUP

rmo2010-001-044

FRONT STORAGE COMPARTMENT

VERIFICATION

PASS

Cover latches properly

FAIL

Cover does not latch

properly

2. Place a sheet of paper on storage compartment

seal.

rbg2010-008-010_a

3. Pull on the sheet of paper.

4. Repeat for the other side.

FRONT STORAGE COMPARTMENT

VERIFICATION

PASS

Sheet not easily

removable

FAIL

Sheet easily removable

5. If any tests fail, adjust front storage compart-

ment cover. Refer to

BODY

subsection in the

proper

CAN-AM ROADSTER SHOP MANUAL

Side Storage Compartment Cover

1. Open and close side storage compartment

cover.

rmr2010-001-002

SIDE STORAGE COMPARTMENT VERIFICATION

PASS

Cover opens and latches

properly

FAIL

Cover does not open or

not latch properly

2. If test fail, adjust latch cable accordingly.

3. Repeat for the other side.

Top Storage Compartment Cover

1. Open and close top storage compartment

cover.

rmr2010-001-003

TOP STORAGE COMPARTMENT VERIFICATION

PASS

Cover opens and latches

properly

FAIL

Cover does not open or

not latch properly

46 / 52

2014-1

PREDELIVERY

Summary of Contents for Spyder RT Limited SE6





















































Search results

Summary of Contents for Spyder RT Limited SE6

Reviews:

Related manuals for Spyder RT Limited SE6

Brands by name

Popular brands

Can-Am Spyder RT Limited SE6, Instructions Manual

Search results

Summary of Contents for Spyder RT Limited SE6

Reviews:

Related manuals for Spyder RT Limited SE6

Brands by name

Popular brands