Can-Am Spyder RT Limited SE6 Instructions Manual Download Page 41

Page: 41 / 52

SETUP

rmr2008-030-009

TYPICAL - LIFT BY THE FRAME

4. To check the drive belt tension use the

BELT

TENSION METER (P/N 529 036 115)

529036115

5. Enter the following specifications to program

the meter.

MASS

WIDTH

SPAN

8.0 g/m

28.0 mm/R

980 mm

rmr2014-032-001_a

SONIC TENSION METER DISPLAY

NOTE:

Refer to the manufacturer's instructions to

set the informations into the device.

6. Turn rear wheel to align a wheel spoke with the

swing arm.

rmr2008-031-003

TYPICAL - SWING ARM ALIGNS WITH A SPOKE

7. Position the sensor under the LH passenger

footrest and hold the sonic tension meter sen-
sor approximately 1 cm (1/2 in) from belt or
closer without touching the belt.

rbs2010-006-001

SPYDER RT

8. Tap the belt to make the belt vibrate and note

the measurement.

9. Repeat step 8.

NOTE:

The second value should be within ±25N.

If no, repeat measurements until tolerance is met.

10. Repeat steps 6 to 9 for the 2 remaining wheel

spokes.

The average of the 3 obtained values (at the 3
spokes) must be within the following range:

DRIVE BELT TENSION

(PARTS AT ROOM TEMPERATURE AND

REAR WHEEL LIFTED)

1050N ± 150N

If the tension of drive belt is out of specification,
adjust drive belt as per

DRIVE BELT TENSION AD-

JUSTMENT

. Refer to

DRIVE SYSTEM

subsection

in the proper

CAN-AM ROADSTER SHOP MAN-

UAL

PREDELIVERY

2014-1

41 / 52

Summary of Contents for Spyder RT Limited SE6





















































Search results

Summary of Contents for Spyder RT Limited SE6

Reviews:

Related manuals for Spyder RT Limited SE6

Brands by name

Popular brands

Can-Am Spyder RT Limited SE6, Instructions Manual

Search results

Summary of Contents for Spyder RT Limited SE6

Reviews:

Related manuals for Spyder RT Limited SE6

Brands by name

Popular brands