background image

Section 01 TECHNICAL MANUAL

Subsection 02 (AIR CONTROLLED SUSPENSION (ACS))

TROUBLESHOOTING WITH
B.U.D.S.

ACS System Leak Test

1. Connect vehicle to B.U.D.S. Refer to

COMMU-

NICATION TOOLS AND B.U.D.S. SOFTWARE

subsection of the appropriate Shop Manual.

2. Select

Activation

page.

3. Select

ACS

folder.

4. Press

Test START

button to proceed.

vmr2010-004-201_a

Step 1: Activation page
Step 2: ACS folder
Step 3: Leak Test START button

After pressing

Test START

button, the com-

pressor will pressurize the air system at 6.5 bar
(90 PSI) for approximately 2 minutes and B.U.D.S.
will monitor the system for any leakage. The
result will be indicated in the TEST STATUS box.

If a leak is detected, pressurize the system again
and inspect hoses and fittings with soapy water
to locate the faulty component.

If no leak is detected from hoses or fittings, in-
spect the compressor check valve and the auxil-
iary line check valve with soapy water.

vmr2010-004-202_b

1. Compressor check valve

vmr2010-004-401_a

1. Auxiliary line check valve

ACS Air Pressure Monitoring

To monitor air pressure in the system during trou-
bleshooting operation, proceed as follows:

1. Connect vehicle to B.U.D.S. Refer to

COMMU-

NICATION TOOLS AND B.U.D.S. SOFTWARE

subsection of the appropriate Shop Manual.

2. Select

Monitoring

page.

3. Select

ACS

folder.

vmr2010-004-301_a

Step 1: Monitoring page
Step 2: ACS folder

PROCEDURES

ACS SOLENOID VALVE

ACS Solenoid Valve Operation Test

1. Connect vehicle to B.U.D.S. Refer to

COMMU-

NICATION TOOLS AND B.U.D.S. SOFTWARE

subsection of the appropriate Shop Manual.

2. Select

Activation

page.

3. Select

ACS

folder.

4. Press

Relief Valve

button to proceed.

vmr2010-004

31

Summary of Contents for 2010 DPS



























































Reviews: