5
because water proximity presents risk, even if the device is turned off.
16. Do not allow the device or power adaptor to wet. If the device falls into water,
immediately remove the power plug or power adaptor from the socket. If the device is
powered, do not put hands in the water. Have the device checked by the qualified
electrician before using it again.
SPEED CONTROL BUTTON (3) Speed Indicator (5b)
Motor speed range : 5 speed levels are available 5000-7000 RPM
Every time you press “+” or “-“ button (3), it will adjust 500 RPM (5b
)
POWER BUTTON / SAFETY LOCK (4)
Press the power button (4) to turn it on or off
Press and hold the power button (4) for 3 seconds, to turn the safety lock on or off
5. LCD Display 5a. Oil Indicator 5b. Speed Indicator 5c. Battery Remaining Capacity 5d. Charge Indicator
To begin charging plug the power cord into the charging Socket (6), and the charger into a 220-240V~ 50/60Hz mains power outlet.
CHARGING THE BATTERY:
When plug the power adapter into the socket, there will be a “beep” and the charging indicator (5d) will start blinking from bottom to
top.
The charging time is about 2 hours. After that the product is full charged, the running time is about 210 minutes.
After the battery is fully charged , there will be a “beep” and the battery capacity reminder (5c) will show 100% and the charging light
(5d)will blink at the same time.
Note: When it runs out of battery, you can use it while charging.
When the battery reaches 10%, 5% 0%, it will beep 3 times. When the battery reduces to
10
%, the charging indicator (5d) will start
blink
24. The charging process should be conducted in temperatures between 5-35 degrees
Celsius.
25.Do not wash the blades in water.
26.Only change comb attachments when the device is switched off.
PRODUCT DESCRIPTION:
6 Charging Socket 7. Combs 7a. Cleaning Brush 7b. Oil bottle
1.
Blade Head 2. Cutting Length Switch 3. Speed button 4. Power Button / Safety Lock
22. The cutting scissors are very sharp. Use caution when assembling, dismantling and
cleaning. Do not touch any elements of the moving blade during the operation!
14.In order to provide additional protection, it is recommended to install residue current
device (RCD) in the power circuit, with residual current rating not more than 30 mA.
Contact professional electrician in this matter.
17. Do not touch the device or power adaptor with wet hands.
18. The device has to be turned off after every use.
15.If using the device in bathroom after use remove the power plug from the socket,
20. Never use this device close to water, e.g.: Under shower, in bathtub, or above sink
filled with water.
19. Do not leave switched on equipment or adapter without supervision.
21. If the device utilises a power adaptor, do not cover it, because this can cause a
dangerous temperature rise and can damage the device. Always connect the power
adaptor cable to the device, and then connect the power adaptor to the power socket.
23.DO NOT CHARGE THE BATTERY FOR LONGER THAN 48 HOURS – this can cause
irreversible damage to the battery.
Summary of Contents for Premium CR 2841
