4
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
Electromagnetic compatibility (EMC)
Low voltage directive (LVD)
Device is compliant with EU directives:
Device is made in class II of insulation.
Device marked CE mark on rating label
13. The outer tube
14. Base
15. Locking nut
3. Loosen the height adjustment screw (12) and set the desired height of the inner tube (11) and then tighten the screw (12).
4. Insert the upper part - the motor housing (6) with a control panel (8) to the inner pipe (11) and tighten the screw (9).
18. The fan set away from curtains, curtains and other items that may be drawn into the fan
running.
4. Rear panel nut
5. Rear panel
6. Motor housing
7. Oscillation lock
8. Control Panel
9. The fastening screw
10. Remote Control
11. The inner tube
12. Height adjustment screw
ASSEMBLY
1. Make sure the power cord is disconnected from the electricity source.
2. Loosen the lock nut (15) from the outer tube (13) and enter the outer tube (13) in the base (14). Screw and tighten the nut (15) from
1. Front Cover
2. Propeller Nut
3. Propeller
19. Do not put any objects into the fan cover. This may cause personal injury or equipment.
DESCRIPTION (Fig.1)
16. Grill-locking screw
the bottom of the base.
5. Unscrew the rear panel nut (4) and mount the rear cover (5) on the motor housing (6), aligning the pins. Screw back and tighten the
rear panel nut (4).
4. MODE - Press the MODE button to set the desired type of wind (NORMAL/NATURAL/SLEEP).
2. To clean the blades of the propeller fan with dust, remove the front cover. Remove the propeller fan from the motor shaft, wipe with a
indicator light will light up on the control panel to show the set speed.
The device switches off automatically when the set time off delay.
8. Connect the power cord to a power source.
5. The remote control range is no more than 10 meters. Functions can also be controlled by using the buttons on the unit.
6. Place the propeller (3) on the motor shaft and screw the propeller nut (2).
7. Align the front cover (1) to the rear (5), lock the clamp and tighten the grill-locking screw (16).
3. OFF - Turn the unit off by pressing the OFF button.
SLEEP. The air flow is automatically reduced by one degree every 30 minutes until reaches small air flow.
CLEANING AND MAINTENANCE
NOTE: Do not allow water to contact the motor or fan buttons.
1. Before cleaning the unit, remove the plug from the socket.
damp cloth, then wipe dry.
3. The body of the motor is dirty, wipe with a slightly damp cloth without detergent. Wipe dry.
2. TIMER - Press TIMER to set the switch-off delay for up to 8 hours. Warning light lights up the set delay.
NATURAL.The device imitates
the natural wind action by changing the fan speed every
few
seconds
4. The device should stored in a dry place.
SPECIFICATIONS:
diameter power/Max.
supply voltage
USING THE MACHINE WITH REMOTE CONTROL (Fig.2)
1. ON / SPEED - Turn on the unit by pressing the ON / SPEED. Press repeatedly to switch between low, medium and high speed. An
CR7314
45 cm
70W/190W
220-240V ~ 50Hz
DEUTSCH
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
LESEN SIE AUFMERKSAM WICHTIGE ANWEISUNGEN BEZÜGLICH DER SICHERHEIT
DER BENUTZUNG BEWAHREN SIE DIESE FÜR DIE ZUKUNFT AUF
2.
Das Gerät ausschließlich an die Steckdose
220-240 V~50 Hz
anschließen. Es darf
nicht zu anderen, bestimmungswidrigen Zwecken benutzt werden.
3.
Wegen Vorsichtsmaßnahmen, sollten keine weiteren Geräte an den gleichen
Stromkreis angeschlossen werden.
1.
Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die
aufgrund von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung
entstanden sind.
5 / 58
Summary of Contents for CR 7314
Page 3: ...2 1 2 ...
